Current location - Quotes Website - Collection of slogans - Data transmission between rtk and computer
Data transmission between rtk and computer
How to input rtk coordinate data?

First, it is necessary to use the correct RTK setting means and related software to correctly configure the RTK positioning system, and then start collecting data.

In the data acquisition stage, RTK coordinates can be recorded in real time, and sensor data can also be cached in the mobile recorder to record the data in the measurement process.

Finally, the collected data are recorded in a computer or GIS for subsequent data processing and analysis.

How to use rtk altimeter?

Familiar with the interface, first enter the main interface of RTK notebook software, and understand the meaning of each icon correspondingly.

Connect the instrument, click Configuration → Manual Port Configuration in the main interface, select Configuration in the lower left corner, select the serial number of the instrument to be connected, and click Next.

Enter the connection password "1234", click Next, then create a new sending port, and click Finish.

Return to the "Manual Port Configuration" interface, select the port number set by the mobile station, and click OK.

Click Configure → Mobile Station Parameters → Mobile Station Options in the main interface to set the broadcast format (consistent with the reference station).

After confirming that the parameters of the mobile station are set correctly, click "Measure" → "Start the receiver of the mobile station" on the main interface, wait for a moment until the display is fixed, and then start the measurement.

To create a new task, click File, select the new task, enter the task name and coordinate system, and then click OK.

Then enter the coordinate system parameter interface, enter the local "central meridian", and click OK.

Click "Measure" → "Point Measure" in the main interface to start the measurement.

Ryder r60rtk manual?

The simple operation steps of Ryder and Kelida RTK: turn on the computer ~ click "Start" in the lower left corner ~ click Egstar.

Step 1: New building

1, project → new project → project name (it is recommended to name it after today's date to facilitate finding mistakes) → OK.

2. Configuration → engineering setting → antenna height: 1.8→ OK.

4. Point information → Check local longitude:119 (119 is greater than decimal place 30 and 1)→ Cancel.

5. Configuration → Coordinate System Setting → Add → Input: A, Parameter System Name, B, Ellipsoid Name (xian80), C, Central Meridian: 1 19→ OK → OK.

Step 2: Collect coordinates and check the measuring point information.

1, measure → point measure → click "a" to collect the coordinates of known points (put the centering rod on the control point, with the bubble in the center) → roll call: t 1→ OK → take the No.2 point according to the above operation (at least 2 known points are required for plane conversion and at least 3 known points are required for elevation conversion), and cancel after collecting points.

Step 3: Find the conversion parameters.

1, enter → find conversion parameters → add → add control points (known plane coordinates: input the coordinates given by the construction party, that is, the coordinates on the drawings) {a, roll call, north coordinates, east coordinates and elevation} → determine to select points from the coordinate management library → select corresponding points → confirm → (collect several known points and repeat this step several times until all the collected known points are available.

2. Save → Apply → Yes (that is, apply to the current project file), and the measurement can be started after applying the parameters.

Point lofting

Measure → point lofting → write → target → add → roll call, north coordinate, east coordinate → confirm → select → confirm → enter the lofting interface, and the information prompt will cooperate with the compass to quickly find the lofting point.

Single point correction:

Input → Calibration Wizard → Next → Input the coordinates of the known points of the current mobile station (roll call; North coordinate; East coordinate; Elevation and antenna height); Place the pole in the center of the control point; Center the bubble → Calibration → OK.

What model of RTK is easy to use?

At present, there are relatively good RTK models on the market, mainly including Huace i80, Zhonghaida iRTK2, Southern Galaxy 1. Here are the core parameters of the three instruments, and the three minicomputers marked above are all core attributes. From the configuration point of view, Huace > China Haida > South.

Chihiro rtk user manual?

Instructions for use of Chihiro rtk

Connect the instrument correctly, turn on the receiver and start collecting stars. Open the phone book and select the connection between Bluetooth and the receiver in the "Configuration" option.

2. Create a new task, select the desired coordinate system and open the task.

3. Set the RF, configure the reference station, start the reference station, and the radio station starts to transmit normally.

4. Configure the rover frequency and radio frequency, start the rover and start the measurement. The above is the simple operation flow of RTK. If a static test is conducted, please set the sampling interval in configationtoolexr software and automatically record the static test after startup.