Question 2: How to open the back cover of Apple notebook and put it on both sides, that is, just buckle the middle part of the side after putting it straight.
Question 3: How to remove the protective case of Apple notebook?
Question 4: How to remove the crystal shell of Apple notebook? Please tell me how to use a hair dryer to blow it at low temperature for a while and then heat it.
Question 5: How to remove the protective shell of the old Apple computer should help you! Hello, landlord! Are you talking about the protective case of the computer? This is very simple. Each shell has a button, just find it and gently mix it outside! Don't push too hard! I hope I can help you!
Question 6: How to disassemble the new back shell of Apple Notebook 20 16 is not difficult! You can look at the model, or at the production model in the computer. Do you want to tell the old from the new or something? Apple has only produced two machines, one black and one white, which is easy to distinguish.
Question 7: How to disassemble the new Apple MacBook Pro notebook correctly and start disassembling it;
The first thing to do is to open the back cover and unscrew the screws one by one. The battery part needs a three-port screwdriver to complete.
Display model A 1286.
Open the back cover
Open the back cover and find that the interior of the new version is almost the same as that of the old version, with no surprise. There is also a warning that it is forbidden to remove the battery.
Open the back cover panorama
Strangely, Apple no longer uses 5-point Torx screws, but uses 3-point screws. It doesn't matter, as long as you have the right screwdriver, you can still unscrew it.
2
Partial battery removal:
The battery shows 77.5Wh, which is a little more than the old version of 73Wh, but it is not enough to improve the battery life of 1 to 2 hours to 8 to 9 hours. Apple may have optimized power consumption.
Battery part
WiFi/ bluetooth module
The location of the WiFi/ Bluetooth module is one of the few places that has changed, and the layout is very similar to the previous integrated MacBook. To remove the AirPort/Bluetooth part, you need to disconnect three antenna connectors first, which can be done with plastic clips.
Disconnect connector
Unscrew the screw
Unscrew the screw
The left side is fixed with one screw, and the AirPort Express card can be separated by unscrewing the other two screws.
three
Optical drive and hard disk part:
The AirPort card is slightly different from the late 2008 version and the 2009 integrated version, while the AirPort/ Bluetooth module is similar to the plastic integrated version of the MacBook.
Airport card
Optical drive, hard disk, etc.
From left to right are Wi-Fi/ Bluetooth antenna, camera cable, optical drive, speaker cable and hard disk.
CD-ROM drive
Due to the redesign of the AirPort/Bluetooth module, the connection is no longer integrated on the camera cable, which greatly reduces the size of the connector. Remove the antenna, and the optical drive part can be removed.
hard disc
Use the same Seagate hard drive as the previous generation.
Unscrew the screw
Plastic strip frame
Removing the speaker and subwoofer module requires removing the four screws attached to the upper cover. Apple slightly changed the design of the speaker module, removing a single plastic strip frame.
four
Antenna and fan part:
Because the AirPort/Bluetooth module is fixed in the Full Metal Jacket, Apple added an antenna and fixed it on the frame of the CD-ROM drive opening. This kind of antenna is invisible on the MacBook integrated body model, which may be because the plastic shell is not effective in RF transmission and reception.
inner structure
Additional antenna
Remove the fan
Remove the logical motherboard.
Logical motherboard
After removing two cooling fans and disconnecting some connectors, the logic motherboard and DC input motherboard can be removed as a whole. The logic motherboard and heat sink are integrated, and the speaker, microphone and interface design have not changed.
five
Panorama of motherboard:
It is labeled as the controller hub of Intel BD 82 HM 55 S LGZS platform. Interestingly, this hub is not connected to the radiator. Obviously, most of the heat has been conducted away from the convection on the surface of the silicon wafer, and a small amount of heat generated by the switching of the graphics card has also been taken away.
Processor and graphics card
hard-working
Intel BD82HM55 S LGZS platform controller hub
The heat sink can be separated from the logic motherboard.
From the perspective of disassembly, Apple's MacBook Pro with Core i5 processor version has not changed much internally, but only made minor changes. At present, 13.3 inch MacBook Pro has adhered to the core 2 processor, and 15 and 17 inch have turned to the core I processor. ...& gt& gt
Question 8: How to remove the back cover of Apple computer needs professionals to do it. If you disassemble it yourself, the screen will break easily. So in theory, only violent disassembly can open the integrated fuselage, but it is basically impossible to put it back. If you want to repair it, you'd better give it to a repair center authorized by Apple.
It takes six screws to open the back cover.
In order to prevent missing parts, the screws of Lenovo notebook cannot be unscrewed, of which the top five cannot be unscrewed, and only the bottom one can be unscrewed.
Unscrew the bottom screw and loosen the other five screws. Don't push too hard when you stop going up at the tinkle.
Screws that can be unscrewed from the bottom of the back cover. You may be nervous for the first time. Slowly pry it open with a thin screwdriver, and then punch out some cards on the left as shown in the figure, that is, gently pry out the back cover there. Lever the top again, the right side and the other three sides are levered, and gently move to the left.
Question 9: How to disassemble the hard shell of Apple Computer 1? First of all, there are no buckles on the lower side of my screen (that is, the side connected to the fuselage). There are two on each side and a long one on it. If yours is the same, it will be easy. Just use one word to change it. Insert a hard flat thing like a knife into the lower buttons on both sides, gently separate the button from the fuselage, then grab the lower corner on the same side and lift it to the other side (pry left and turn right, pry right and open it).
Question 10: Where can I change the case of an Apple laptop? It is integrally formed. It is best to go to the official after-sales replacement, which is guaranteed and justified.
If it is replaced by a third party, it may lead to replacement of spare parts or replacement of defective materials.