First, set the network card IP to 10. 1. 1.x?
Type10.1.1.1?
The login box appears, and enter the user name and password (default user name: admin password: admin)?
After entering the configuration page, click Services > NAT in the left navigation bar to enter the network address translation (NAT) configuration interface, click the drop-down list box, select the NAT rule entry, and click Add to add a new entry?
Enter the "NAT Rules-Add" page to add NAT rules. This is the most important one:
Because multiple ports are used, in the following example settings, the port is set as a segment, and different ports may use different protocols, so the protocol also uses the default ALL. In short, for convenience, you can make a rule. ?
Rule type: RDR takes precedence?
Rule ID: the serial number of the rule, just fill in an unused number?
If Name: Default All?
Agreement: Any?
"Local address source" and "local address destination" respectively fill in the starting address and destination address of the local address, that is, an address segment of the intranet. ?
If the "global address source" and "global address end" are ADSL dynamic dialing, the cat will set them automatically if all zeros are filled in.
Port of destination Source: Wagga Port?
Terminal of destination port: Wagga port?
Local port: Wagga port?
After setting, click the Submit button below to close the NAT Rule-Add interface and the Network Address Translation (NAT) Rule Configuration interface. ?
That is, click "Management"-> in the left navigation bar; "Confirm &; Restart. " In the confirmation &; In the "Restart" interface, click the "Confirm" button, and then click "Restart" to make the configuration effective.
Linksys series router port mapping
The default address of linksys router is192.168.1.1?
Enter the address of the local router in the address bar of IE, for example, 192. 168. 1. Click GO IE, and a window will pop up asking for the login name and password of the router. The factory default setting of linksys is that the login name is empty and the password is admin. Then click OK. ?
If the password is correct, IE will enter the settings page of Linksys and click the "Advanced" column in the upper right corner; ?
After entering, click the second big item on the top left and select "Forward"; ?
After entering the "forwarding" column, you need to forward two ports, one is the port of TCP (vaga port number) and the other is the port of UDP (vaga port number).
1. Give these two port images a name?
2. Here you need to fill in the port required by vagaa, and the first line is the port of TCP; Fill in the UDP port in the second line, you can change these two ports, but they should be consistent with the settings in vagaa?
3. Fill in the IP address of the local intranet here. Sometimes the intranet IP of a computer will change. Once it changes, you need to come back here and change this IP address to point to your new IP. ?
Then tick the place where the "X" is placed in the interface; ?
Finally, click "Apply" to save.
Speedtouch 500 series port mapping
The factory-defined router address of Speedtouch is 10.0.0. 138?
In the advanced column on the left, you will see the NAT option (if you don't see it, please click the advanced and drop-down menu, and the NAT option will appear). After clicking NAT, the NATP Settings window will appear. ?
1, click New, then select tcp in Protocal, fill in the internal IP address of this machine in inside IP, fill in the port of vagaa in Inside Port (you can change it at will, but make corresponding changes in vagaa), keep 0.0.0.0 in Outside IP, fill in the same port as the previously filled in Inside Port in Outside Port, and then click Apply; ; ?
2. Click NEW again, then select UDP in Protocal, fill in the internal IP address of your computer you copied earlier in Inside Port, fill in the port of vaga (you can change it at will, but make corresponding changes in vaga), keep 0.0.0.0 in Outside IP, fill in the same port as the previously filled-in Inside Port in Outside Port, and then click Apply. ?
3. Click Save All on the left to save the settings.
Port mapping of topstar TE-SR400 router
1. Visitors who enter in the address bar must access the FTP service through "FTP://218.70.130.155: 8021". ?
5. "Server IP address" refers to the private IP address of the computer where the server is set. In this example, the IP addresses of FTP server and Web server are192.168.10.11. ?
6. "Server port number" refers to the port opened by the server for its own service. In this example, both FTP server and Web server use their own default ports: 2 1 and 80?
After adding the mapping project, click Finish to complete the setup. Then select Save and Restart, click Save in the pop-up dialog box to save the settings, and then click Restart to restart the ADSL modem (Note: this order must be observed! Otherwise, the configuration just made will not be saved). ?
After the ADSL modem is restarted, Internet users can directly access various services set by the "internal" computer through the public IP address of the ADSL modem.
Port mapping of TP-LINK TL-R402M broadband router
1, login to the configuration page, and the default address is192.168.1.1,user name admin and password admin; ?
2. Enter the "Forwarding Rules"-"Virtual Server" tab; ?
3. Write the vagaa port number (shown as 4662) in the "service port" of the virtual server operation interface; Write the last string of numbers of the computer IP address in the last space of "IP address"; Select TCP in "Protocol" and select the "Enable" radio box; ?
4. If there is another service port number (for example, mule port number is TCP:4662 and UDP:4672, but vagaa's TCP and UDP are the same), please operate as shown below; ?
5. Save the virtual server interface and start vagaa. ?
Port mapping of UCOM youkang series routers
By default, the addresses of Youkang routers are192.168.6438+023.254?
Open IE, enter the router address192.5438+068.438+023.254 in the address bar, and press enter. ?
Enter the router setup screen, then you will be asked to enter the router login password, the password is admin, and then click "Login" to enter the setup screen. ?
On the right side of the setup screen is the administrator's main menu, as shown below. Find "Advanced Settings" and click it, and three submenus will appear. Click on the first item "Virtual Server"?
At this time, a few lines of small boxes as shown below will appear in the main window on the right for filling in. ?
Fill in 4662 (such as Vagaa port number) 19 (own ip) and tick the startup box?
4672 (ditto) 19 (ditto) tick the startup box?
Alcatel S6307KH port mapping
Change the local ip to192.168.1.1,and the subnet mask is 255.255.255.0. ?
After the configuration takes effect, visit http:/192.168.1.254/in IE, and the user name and password are root. ?
Add an entry in it, the protocol is TCP, the interface is local WAN interface, the service name is vaga, the port number is vaga, and the server ip is local internal ip, such as19.168.1.65438, and the server port number is 4662?
In the same way, add another one, the protocol chooses UDP, the port uses vagaa, and everything else is the same. ?
Then save and restart the router.
Bell 6309 port mapping
This router is configured in the line configuration. ?
Take setting up a web server as an example. The LAN address of the router is 192. 168. 1, and the ip address of the web server is192.168.1.2 (it must be in the same network segment as the ip of the router LAN). Specifically:?
In the "Inbound" of "Nat" of "Line Configuration"
Port: 80
Moderator:192.168.1.2,
Protocol: tcp?
Then "add" will do.
Shanghai Nortel BD20 1 Routing Settings
First, start IE, enter 192. 168. 1 in the address bar, and enter admin and dare in the account and password fields of the new window respectively (note that both are lowercase)?
1, turn off the virtual circuit 1-7 in the WAN settings, and only keep the virtual circuit 0; ?
2. Set VPI=0 VCI=35 for virtual circuit 0 (values vary from place to place, please refer to the values of local telecom to fill in correctly); ?
3. Set the packaging protocol of virtual circuit 0: PPPOE LLC;; ?
4. Set the bridge of virtual circuit 0: DISABLE;; ?
5. Set your own broadband account and password (that is, the account and password set when opening ADSL at the telecom counter); ?
6. Tick before automatic reconnection; ?
7.NAT is set to NAT; ?
8.DNS is set to the DNS value of local telecom; ?
9. Save the settings and restart ADSL Cat. ?
Description: Before setting up ADSL Cat, please set your network card as manual IP, with IP address 192. 168. 1. x (x value is between 2 and 254) and gateway192.168. The value of DNS can be filled in with reference to the value in step 8 above.
Tisch
1, safety is the guarantee of a happy family, and accidents a