1-stom box block selection, vypyr? 15 not applicable.
2-amp speaker analog selection, turn this button to select the desired speaker type, and the corresponding indicator light will be on. Press this button to switch between the silent channel and the distorted channel of the speaker. If the light is red, it means it is in the distorted channel, and if the light is green, it means it is in the unvoiced channel. Hold it.
2 seconds to enter the tuning mode and press the button.
3 Display sound level. If the green light is at 12, it needs to be lowered on the right and raised on the left. When all the lights are on, the sound standard will be explained.
3- Effects Select various effects, press the button to enter the edit mode, and the edit indicator light will be on (Edit? Mode light).
4- Pre-gain pre-amplification gain, distortion adjustment, used to control the effect parameter 1 in edit mode.
5- Low and low frequency adjustment, used to control effect parameter 2 in edit mode.
6-mid intermediate frequency adjustment, control the delay times in edit mode.
7- High-frequency adjustment, control the volume of delay in edit mode, the button indicates from left to right from 0 to the maximum, and the minimum value is equal to no delay.
8-column gain
The latter stage amplifies the gain and controls the analog speaker.
The volume of the amplifier (button 2) controls the reverberation value in edit mode.
9-Aux input, you can connect mp3, mobile phone, cd player and other playback devices.
10- the main volume of the main speaker.
12- power supply
Power switch.
13- preset tone switch button,
12 factory preset timbre. Divided into three groups: A, B and C, each group has four timbres. Press the leftmost button bank.
Select a group, and then select a tone from the four tone buttons on the right. When you have finished editing the timbre that you think is good, you can save the current timbre by holding down any timbre button that you want to save in the current group. Of course, the timbre before this button is covered.
14-Tap？ Speed button, used to set the delay time. Usage is to press this button twice in a row, and the interval between two times is the delay time, which is equivalent to setting a delay millisecond on the effector.
15- Edit mode. Press the effect button (button 3).
You can enter edit mode and click it again to exit edit mode. Adjusting delay or reverberation requires entering edit mode.
16- headphones/recording output jack. Budweiser said that they spent a lot of energy to ensure that this jack reached the quality of the recording studio, of course, with the right equipment (they didn't bring their own). When using the earphone, the speaker is muted, and the master (key 10) controls the earphone volume.
Hint 1:
Why are these little lights flashing all the time?
When the guitar is not plugged into the speaker, these lights will flash by themselves (I don't like screensavers very much). Don't worry, plug in the guitar and the light show of the speaker will stop automatically. Turn on the speaker. If the guitar cable is plugged in, the light show will be turned off. If you want to disable this feature completely, just hold down the first button at the same time.
4 preset the tone preset button, and then turn on the speaker power switch to cancel the preset. This function has been disabled the next time the speaker is powered on.
Tip 2:
When you rotate a button, the corresponding LED light will indicate the selected item or numerical size in the current button list.
Tip 3:
Edit status: press the effect button to enter the edit mode and edit the indicator light at the same time. Mode) is turned on, and effects and parameters such as reverberation and delay can be controlled in editing state (effect button, parameter 1, parameter 2). Press this button again to close the edit mode and edit the indicator (Edit? Mode light) goes out.
Note: In edit mode, the effects listed below the buttons are controlled. In non-editing mode, distortion, volume and low, medium and high frequencies can be directly adjusted.
Speaker analog part:
The characteristic of Vypyr is that each speaker has two channels: unvoiced and overloaded. Just press the button to select the channel. When the LED light is green, it is currently a clean or green channel, and when the light is red, it is a distorted channel.
Twn
Green channel: Very bright and clean timbre, which is the standard unvoiced timbre for many guitarists. Red channel: this channel obtains the thermal distortion timbre of the electron tube with reverberation.
Dlx
Green channel: classical timbre.
Red Channel: hot-roded? Dlx distorted timbre.
Puglisi
Green channel: classic rock timbre.
Red Channel: hot-roded? Plxi strongly distorted timbre.
Brit (UK)
Green channel: British timbre.
Red channel: British distorted timbre.
B-Kat
Green Channel: Stack now rock distorted timbre.
Red channel: the timbre is stronger than the green channel, and the distorted timbre is good.
Classic Budweiser? One of the 50 classic speakers.
Green channel: unvoiced sound.
Red channel: the main channel.
XXX
Green channel: triple? XXX silent channel.
Red channel: triple? XXX？ Hyperdistortion channel.
JSX (Joe? Satriani timbre).
Green channel: JSX? 2 12? Extrusion channel
Red channel: JSX? 2 12? Super channel.
6505 simulates the classic Budweiser 6505 speaker.
Green channel: 6505? Besides? Extrusion channel
Red channel: 6505? Plus the main channel.
Rec is a high gain speaker. Although it is not as heavy as 6505, it has a good tone.
Green channel: "orange" orange channel.
Red channel: "Red" channel.
K-Stein is similar to Rec.
Green channel: Tightening the high gain channel.
Red channel: high gain channel.
The adjustment of timbre requires you to ponder over it. Fine-tune the parameters of each knob. Repeated operations will gradually understand. Feeling is very important.