If it is a clean room in the electronics industry, it is necessary to strictly control static electricity, so there are anti-static requirements for materials, tools and packaging. People who come into contact with the product.
General prohibition and precautions of 10 thousand class clean room
(1) Personnel who have not obtained the qualification to enter the clean room are not allowed to enter the clean room.
(2) It is forbidden to touch the product with bare hands.
(3) Forms, operation cards, record books, etc. It should be filled in carefully, and any alteration must be signed and dated.
(4) Gloves should be kept dry and clean, and do not scribble on them.
(5) It is forbidden to sit and lie on the desktop, pedal, floor, trash can, guardrail, and recline on the machine or locker.
(6) If your hands are prone to sweating or allergies, wear cotton gloves first, then PVC gloves or latex gloves.
(7) Pay attention to all announcements and slogans at any time.
(8) We should actively support each other, but we should not operate unqualified machines alone.
(9) Everyone should prohibit and correct personnel, articles, labels, etc. Found not in conformity with the provisions, put forward at any time, and notify the relevant competent personnel.
(1) Always be careful not to show your hair, mouth or nose.
(2) Do not put dust-free clothes, hats, etc. Leave it on the floor at will.
(3) You can only wear and take off dust-free clothes in the locker room, but not in other places.
(4) The front and rear doors of the shower room cannot be opened at the same time.
(5) It is forbidden to run, play, make noise or sleep. In a clean room of ten thousand levels.
(6) It is forbidden to eat and drink in ten thousand clean rooms.
(7) In the clean room, people should be avoided from getting together to avoid particles. microparticle
(8) After strenuous exercise or sweating, don't enter the clean room immediately until you breathe smoothly and stop sweating.
(9) If you smoke, you must wash your hands and rinse your mouth within 30 minutes after smoking before entering.
(10) General paper, notebooks, cartons, toilet paper, books, pencils, correction fluid, erasers and other non-dust-free items are not allowed to be brought into the clean room in front of the panel.
(1 1) Grinding, filing, sawing, sandpaper, abrasives, etc. are strictly prohibited. It is also forbidden to use it in a clean room.
(12) The personnel working in the class 10,000 clean room should keep their hair and body clean and wash their hands frequently.
(13) Personnel entering the clean room are forbidden to use cosmetics such as perfume, lipstick and hair gel. Those who have makeup should remove their makeup first.
You can go in.
(14) Raw materials must be unpacked and wiped before entering the clean room.
(15) Never talk to the machine in the product, cassette or chamber.
(16) Even if gloves or finger covers are worn, unnecessary contact with products must be reduced.
(17) Documents, semi-finished products, articles or production tools in the clean room shall not be taken out without the permission of the department head.
(18) Don't pull down your mask when you speak.
(19) When using the telephone in the clean room, it should be concise and to the point, and the line is not busy.
(20) The escape route in the clean room should be barrier-free.
(2 1) Ten thousand clean indoor articles, chemicals, cassettes, tools, documents, record books, etc. Should be placed neatly.
(22) Before entering the shower room, both feet should step on the sticky pad to remove the dirt on the dust-free sole.
(23) The correct action of air shower should be to raise your hands and turn your body slowly (at least three times).
(24) Each shower room has a specified number of people, which cannot exceed the specified number. If there are too many people, you should enter in batches.
(25) The safety door is only used in an emergency, and it is forbidden to enter and leave the factory through the safety door at ordinary times.
Dust-free clothes/shoes should not leave the dust-free room, and electrostatic shoes should not leave the factory area.