Current location - Quotes Website - Personality signature - How to refuel the atomic oil seal?
How to refuel the atomic oil seal?
How to refuel atomic articles

Lesson: Last year, my company's atomic seal faded, so I bought atomic seal oil outside. After the second time, it was not good, only oil was left, and an atomic seal was broken.

I asked the relevant departments of the Public Security Bureau to know that I should buy the atomic stamp oil of the seal company (we sell it at the service window of the Public Security Bureau here).

If you are in trouble, find the department that engraves your seal, otherwise it will be very troublesome to dismantle it. Engraving a new chapter is a trivial matter, but the trouble is to go to the bank to change it.

How to clean the official seal of atomic seal mixed with oil,

Remove the seal, wash the sponge with soap or washing powder, press and suck the seal with a paper towel, and then combine and add the correct printing oil after it is completely dried. I didn't dare to wash the sealing surface, because it is said that there are n micropores on the sealing surface, which is particularly easy to block. It took a whole morning to press and absorb ink, half a box of tissues! Wrong printing ink must be thrown away!

How to open this atomic chapter?

Chapter handles of this structure are usually connected by threads. You can try to unscrew it. If you can't twist it, you should plug it (such a big chapter should not be plugged). After disassembling the handle, you can see the ink bag. The upper end of the ink bag is usually a rubber plug. Open or unscrew the ink bag cover, inject ink, and then assemble.

How to refuel the atomic seal? How to refuel in atomic chapter?

You have to use special oil, just buy a bottle of oil, and you will know how to add it. It's simple.

How to clean the official seal when it is added to atomic oil by mistake?

Don't be nervous, there are many ways.

You can wipe it with Tianna water.

Get some gasoline. No problem.

If it is red rubber, be careful. Just squeeze the water out with a non-woven fabric or a wet towel.

Can the official seal of atomic oil be mimeographed?

The official seal of atomic oil can be printed with oil.

The official seal of atomic oil should be stamped with the professional seal of atomic oil, and it is not allowed to refuel indiscriminately, otherwise it will damage the official seal.

Atomic seal belongs to modern high-tech products. It stores the ink in the inner core of the seal, and then makes the inner core into the shape of the printing surface, so that the ink oozes from the inner core every time the seal is stamped, and it is not necessary to print the ink on the printing table every time the seal is stamped, which improves the efficiency of office production.

Atomic seal printing method:

1. Pour 15ml of professional seal oil for atomic seal into a flat-bottomed vessel (the volume of the vessel is slightly larger than the size of the seal).

2. Pour the printing surface of the atomic seal into the printing oil once (leave it for about 12 hours).

3. After the ink is absorbed by the seal, take it out and wipe off the excess ink around the seal with a paper towel.

How to oil photosensitive seal?

So adding a little oil before using a small amount can save and protect the seal. Refueling method: Take off the seal cover, make the words face up, and smear the seal border, font and five-star (picture) with a small amount of photosensitive ink. After the oil slowly penetrates, apply it several times according to the situation. Then wipe off the excess oil with a clean soft cloth or paper towel, so that it can be used immediately. Second, when photosensitive seals are used in large quantities, the above refueling methods are not available. Oil should be filled through the oil filler below the seal handle. Methods: Put the seal on the table, hold the oil filler cover at the lower part of the handle hand in hand, take a small bottle of ink (if it is a large bottle, it is best to use a syringe or the like), aim the tip of the bottle at the oil filler, and add the ink drop by drop. If the oil filler is too small, you can gently shake the seal to let the oil flow in naturally. Generally, there is an oil storage sponge in the photosensitive seal, which will temporarily absorb excess oil and then slowly penetrate down to the photosensitive pad, so when using a small amount of seal, don't refuel like this! Thirdly, there is another oiling method, that is, take off the photosensitive pad, put it in ink and put it on casually. The ink should not exceed the thickness of the photosensitive pad, so that the photosensitive pad can slowly absorb the ink. If the seal has a sponge, you can put some oil in it. After the photosensitive pad is completely filled with ink, take it out and put it into a sealed shell.

How to refuel atomic articles?

Buy a bottle of atomic chapter stamp pad, after work, preferably on Friday (because you don't go to work on Saturday/Sunday, you may not need a seal).

Spread atomic oil evenly on stamps, not too much, so that stamps can eat enough oil. Too much oil is a waste, it can't be used after adding oil, and the seal is messy.

Then put on the oiled seal and turn the downward seal upward. You can use it at work on Monday.

But first cover a piece of waste paper twice (press it) to make the oil even.

How to refuel photosensitive seal

First, use the refueling method many times. Some seals may only be covered several times at a time. If you refuel too much, it is also a waste to put it there. And after a long time, the ink will evaporate and thicken, which will cause damage to the gasket. So add a little oil before using a small amount, which is economical and protects the seal. Remove the seal cover, let the text face up, and smear the seal border, font and five-star map with a small amount of photosensitive ink. After the grease slowly penetrates, apply it several times according to the situation, and then wipe off the excess grease with a clean soft cloth or paper towel, which can be used immediately. 2. When photosensitive seals are widely used, the above oiling method cannot be used. The seal should be oiled from the oil filler at the lower part of the handle. Put it on the table, pull down the cover from the oil filler at the lower part of the handle and take a small bottle of ink. If it is a large bottle, it is best to use a syringe. The tip of the bottle mouth is aimed at the filler, and ink is added drop by drop. If the oil inlet is too small to add the seal smoothly, you can gently shake the seal to let the oil naturally flow into the photosensitive seal. Generally, there is an oil storage sponge, which will temporarily absorb excess oil and then slowly penetrate down to the photosensitive pad, so when using a small amount of seal, don't refuel like this. Thirdly, there is another oiling method, that is, take off the photosensitive pad and put it in ink. Literally, the ink should not exceed the thickness of the photosensitive pad, so that the photosensitive pad can slowly absorb the ink if a seal is used.