1. Does the quality acceptance of inspection batches and sub-projects not include?.
A. The quality of the main control items and general items has passed the sampling inspection
B. The quality acceptance records of the inspection batches included in the sub-projects should be complete
C. Have complete construction operation basis and quality inspection records
D. Visual acceptance
Correct answer? D
2. Surface vibrators are mostly used for vibration. Real ( ) concrete.
A. Thick structural components
B. Thin components such as floors and floors
C. Vertical components with small cross-section and dense steel bars
D. Prefabricated roof panel components
Correct answer?B
3. Which of the following projections is a parallel projection? ?
A. Top view
p>B. An elongated figure under the street lamp
C. Project the calligrapher’s original handwriting onto the wall using electric light
D. Use an incandescent lamp as the Shadow puppet of the light source
Correct answer? A
4. Which of the following statements about the effectiveness of the law is incorrect ( ).
A. The effectiveness of laws is lower than that of the Constitution? But higher than other laws
B. The effectiveness of administrative regulations is lower than that of the Constitution and laws
C. Local governments The effectiveness of sexual regulations is lower than that of the constitution, laws and administrative regulations
D. The effectiveness of administrative regulations is lower than that of the constitution, laws, administrative regulations and local regulations
Correct answer?D
5. The dimensions marked on the diagram are composed of.
A. Extension lines, dimension lines, dimension numbers and arrows
B. Extension lines, dimension lines, dimension start and end symbols and dimension numbers
C. Dimensions Boundary lines, dimension lines, dimension numbers and units
D. Dimension lines, start and end symbols, arrows and dimension numbers
Correct answer? B
6. Generally believed ?75% of the cost of a building’s life cycle occurs.
A. Planning stage
B. Operation and use stage
C. Construction stage
D. Design stage
The correct answer? B
7.
The brick foundation is stepped and enlarged step by step. Generally, every 2 bricks are picked out and laid.
A.1/2 brick
B.1/4 brick
C.3/4 brick
D.1 skin Brick
Correct answer? B
8. For construction units that require rework or reinforcement, they should submit an investigation report and a treatment plan approved by the design and other relevant units to the supervision agency.
A. Quality problems
B. Quality accidents
C. Quality defects
D. Unqualified quality
< p> The correct answer? B9. The number of years of professional practice at the construction site of a data clerk with a secondary vocational education in civil engineering related majors is?
A.1.0
B.2.0
C.3.0
D.4.0
Correct answer?D
10. The following do not belong to the construction project safety organization The measures are.
A. Establish a construction project safety organization system
B. Regulations on safety technical requirements for construction sites? Safety of various professional types of work
Technical operating procedures? Equipment maintenance Maintenance system, etc.
C. Establish a safety responsibility system for each major, department, and production position that matches the project safety organization system
D. Establish the safety production responsibilities of the project manager and the safety production responsibilities of project team members
Correct answer? B
11. The characteristics of congruent rhythm flow are ().
A.K>ti
B.K< ti
C.K=ti
D. None of the above
Correct Answer? C
12. When the machinery is idle due to lack of work? The shift fee of the machinery and equipment can be calculated accordingly.
A. Shift fee or depreciation fee
B. Shift fee and depreciation fee
C. Leasing fee or depreciation fee
D. Lease fees and depreciation fees
Correct answer? C
13. Administrative penalties are implemented by administrative agencies or organizations authorized by laws and regulations against citizens who violate regulations. A specific administrative act in which a legal person or other organization adopts punitive sanctions.
A. Administrative procedures
B. Behaviors stipulated in civil law
C. Articles of association of social groups
D. Relevant provisions of criminal law
p>
Correct answer? A
14. When the groundwater level is very high and the foundation cannot be buried above the groundwater level, in order to reduce and avoid the buoyancy and influence of groundwater, the bottom surface of the foundation should be buried to? .
A. The highest water level is below 200 mm
B. The lowest water level is below 200 mm
C. The highest water level is below 500 mm
D .Between the highest water level and the lowest water level
Correct answer?B
15. Common types of civil liability for engineering construction include.
A. Fine
B. Fine
C. Confiscation of illegal gains
D. Compensation for losses
The correct answer is D
16. The construction unit shall notify the project quality supervision agency responsible for supervising the project in writing of the time, location and name of the acceptance team ? working days before the completion acceptance of the project.
A.5.0
B.6.0
C.7.0
D.14.0
Correct answer? C
17. Construction enterprises must establish and implement a normalized safety inspection system and enterprise safety management organization.
A. No less than once every two months
B. No less than once a week
C. No less than 2 times a month< /p>
D. No less than once a month
Correct answer? C
18. The project supervision unit should review the safety technical measures or special projects in the construction organization design Does the construction plan comply with the requirements?
A. Contract
B. Mandatory standards for engineering construction
C. Design requirements
D. Recommended standards for engineering construction
The correct answer? B
19. The construction unit shall comply with the "Regulations on the Record Management of Completion Acceptance of Housing Construction and Municipal Infrastructure Projects" within days from the date when the project is completed and accepted. According to the provisions of Order No. 2 of the Ministry of Housing and Urban-Rural Development, it shall be filed with the construction department of the local people's government at or above the county level where the project is located
A.28.0
B.30.0
C.14.0
D.15.0
Correct answer? D
20. According to the "Code for Calculation of Building Area of ??Construction Projects"? Curtain wall is used as Envelope components? Yes.
A. Curtain wall center line
B. Curtain wall outer edge
C. Curtain wall inner edge
D. Main structure outer edge< /p>
The correct answer? B
21. Among the following geometric bodies, which one has the same front view, left view, and top view? ?
A. Sphere and cylinder
p>B. Cylinder and cone
C. Cylinder of cube
D. Sphere and cube
Correct answer?D
< p> 22. Which of the following standards does not belong to the core standards of the ISO9000 2008 family of standards?A.ISO19011?2000 "Quality Management System - Audit Guide"
B.ISO9000?2005 "Quality Management System - Basics and Terminology"
C. ISO9001?2008 "Quality Management System - Requirements"
D.ISO9004?2009 "Quality Management System - Performance Improvement Guide"
Correct answer? A
23 . Generally, the thickness of the protective layer in the beam is
A.10mm
B.15mm
C.20mm
D.25mm
p>The correct answer is D
24. Administrative regulations refer to normative documents formulated in accordance with legal procedures.
A. National People’s Congress and its Standing Committee
B. People’s Congress at or above the county level and its Standing Committee
C. State Council
D. People's governments at or above the county level
Correct answer? C
25. The principles of the Tort Liability Law apply to high-altitude throwing objects.
A. Principle of presumption of fault
B. Principle of no-fault
C. Principle of fault
D. Principle of fairness
Correct answer?D
26. Calculation of balconies of buildings according to "Code for Calculation of Building Area of ??Construction Projects" GB/T50353-2013.
A. The enclosed balcony shall be based on its horizontal projected area
B. The unenclosed balcony shall be 1/2 of its horizontal projected area
C. Within the main structure Calculate the total area based on the peripheral horizontal area of ??the structure
D. Calculate the overall area based on its horizontal projected area
Correct answer? C
27. The floor layer is usually composed of.
A. Surface, floor, and floor
B. Surface, floor, and ceiling
C. Support, floor, and ceiling
< p> D. Cushion, beam, floor slabCorrect answer? B
28. ?Easy to construct? But prone to condensation and dust? Large thermal conductivity.
A. Watered terrazzo floor
B. Cement mortar floor
C. Wooden floor
D. Prefabricated terrazzo floor
p>
Correct answer?B
29. Which of the following projections is the central projection? ?
A. Three views
B. Human vision
C. Oblique dichotomy
D. Projection of a person under the noon sun
Correct answer? B
30 . The PDCA in the PDCA cycle refers to respectively.
A. Plan, check, implement, handle
B. Plan, handle, check, implement
C. Plan, implement, check, handle
p>D. Inspection, planning, implementation, disposal
Correct answer?C
31. Does the necessity of construction project data management not include?
A. Construction project data is an important part of urban construction files
B. Construction project data management is the basis for design
C. Construction project data is the processing of project quality and safety accidents Important technical basis
D. Strengthen engineering data management? You can urge each unit and individual to work in accordance with standards, specifications and procedures
Correct answer? B
32. According to the "Code for Calculation of Building Area of ??Construction Projects", the building area of ??buildings with curtain walls as enclosure components should be calculated according to.
A. Horizontal area of ??the outer wall of the building
B. Enclosure area of ??the inner side of the curtain wall
C. Enclosure area of ??the center line of the curtain wall
< p> D. Enclosing area of ??curtain wall exterior lineCorrect answer? D
33. What is the notice of intention to claim? Table
A. Meter used by the construction unit
B. Supervision meter
C. Construction unit meter
D. General meter
Correct answer? D
34. The steel bars in reinforced concrete structures that bear the tensile and compressive stresses in mechanical calculations are called
A. Stress-bearing steel bars
B. Erection bars
C. Stirrups
D. Distribution bars
Correct answer?A
35. Evaluation of professional abilities of professionals at construction and municipal engineering construction sites ?Should be implemented by a unified organization.
A. National housing and urban-rural development administrative department
B. County-level housing and urban-rural development administrative department
C. Municipal-level housing and urban-rural development Administrative department
D. Provincial housing and urban-rural development administrative department
Correct answer? D
36. Which of the following foundations is a flexible foundation?
A. Reinforced concrete foundation
B. Rough stone foundation
C. Brick foundation
D. Plain concrete foundation
Correct answer? A
37. The order of formwork removal for ribbed floor slabs is generally ( )
A. Column formwork→slab bottom formwork→beam side formwork→beam Bottom formwork
B. Column form → Slab bottom form → Beam bottom form → Beam side formwork
C. Column form → Beam bottom form → Beam side form → Slab bottom form
p>
D. Column form → Beam side form → Slab bottom form → Beam bottom form
Correct answer? D
38. Leakage protector test? No less than 1 Times
A. Every day
B. Weekly
C. Monthly
D. Every 10 days
< p>Correct answer?B39. The situation where the supervisor issues a supervision notice does not include?.
A. Violation of design requirements during the construction process
B. Use of unqualified materials, components and equipment
C. Quality and safety accidents in the project
D. Violations occurred in aspects such as safety production management and construction progress
Correct answer? C
40. The chief supervising engineer shall not entrust the following work to the general manager Supervision engineer representative? Which is incorrect?
A. Organize the preparation of supervision plans and review and approve supervision implementation details
B. Allocate supervision personnel according to project progress and supervision work conditions
C. Organize and review the construction organization Design, (special) construction plan
D. Acceptance of concealed projects
Correct answer? D
41. The width of the object can be reflected in the three-sided view.
A. Front view
B. Side view
C. Floor plan
D. Oblique projection
E. Cross-sectional view
Correct answer? B, C
42. The supervision information form signed by the chief supervisory engineer and stamped with the professional seal includes?.
A. Project start order
B. Project suspension order
C. Project resumption order
D. Supervision notice
p>E. Project payment certificate
Correct answer? A, B, C, E
43. The components of legal liability are.
A. There is a fact of damage
B. There is an illegal act
C. There is a causal relationship between the fact of damage and the illegal act
D. At fault
E. At fault
Correct answer? A, B, C, D
44. It does not belong to the function of applying cold base oil yes.
A. Prevent linoleum bubbling
B. Waterproofing
C. Good air tightness and heat insulation
D .Adhesive waterproof layer
E. Cold protection function
Correct answer? A, B, C
45. The job knowledge that a data clerk should possess includes?.
A. Standards and management regulations related to this position
B. Project completion acceptance record management knowledge
C. Urban construction file management, construction data management and Basic knowledge of construction industry statistics
D. Basic knowledge of secretarial and official document writing
E. Knowledge of data security management
Correct answer? A, B, C, E
46. The characteristics of construction project documents include?
A. Dispersion and complexity
B. Economy
C .Comprehensiveness and authenticity
D. Randomness
E. Multi-professionalism and comprehensiveness
Correct answer?A,C,D,E< /p>
47. What are the three stages of BIM technology serving in the field of construction engineering?
A. Design
B. Construction
C. Operation
D. Research
E. Environmental assessment
Correct answer? A, B, C
48. The scaffolding was removed in the wrong order Yes
A. Layer by layer from top to bottom? Install first and then dismantle? Install first and then disassemble.
B. Layer by layer from top to bottom? Install first and then disassemble? Install then. Disassembly
C. From both ends to the middle? Install first and then disassemble? Install first and then disassemble
D. From both ends to the middle? Install first and then disassemble? Install then disassemble< /p>
E. Install later and dismantle first
Correct answer? B, C, D
49. The factors that affect the foundation depth are:
A. Level of groundwater level
B. Depth of frozen soil line
C. Burial depth of adjacent foundation
D. Upper load size
E. Annual rainfall
Correct answer?A,B,C,D
50. Foundation pit support engineering information includes?< /p>
A. The excavation and support construction of foundation pits should comply with current standards and specifications, and a special construction plan should be prepared
B. Experts should be organized to demonstrate if the excavation depth exceeds 3m< /p>
C. Experts should be organized for demonstration if the excavation depth exceeds 5m
D. After the construction of the deep foundation pit retaining structure is completed and before the construction of the underground structure project, it must be carried out by the construction, The design, construction and supervision units of deep foundation pits shall jointly accept the deep foundation pit project
E. For cases with a long construction period, if the backfilling is not timely or the foundation pit support exceeds the designed service life, experts should be organized in time Make a return visit
Correct answer? A, C, D, E
51. Water supply and drainage systems can be divided into ( ) according to their functions? Pipes and fittings used in different systems , various valves and other materials are different.
A. Hot water system
B. Cold water system
C. Pressure system
D. Pressureless system
E. Reclaimed water system
Correct answer? A, B, C, D
52. Should the supervision report be sent to?
A. Competent department
B. Construction unit
C. Project supervision unit
D. Construction unit
E. Project supervision organization
Correct answer?A,C,D,E
53. The following are spatial parameters ( ).
A. Working surface
B. Number of construction sections
C. Number of construction processes
D. Flow intensity
< p> E. Construction qualityCorrect answer? A, B
54. Unless otherwise agreed in the special contract terms, the measurement of the unit price contract shall be carried out in accordance with the following agreements
A. The contractor shall submit to the supervisor on the 25th of each month a report on the work volume completed from the 20th of the previous month to the 19th of the current month
B. The contractor shall submit to the supervisor on the 20th of each month Submit the work quantity report completed from the 20th of the previous month to the 19th of the current month
C. The supervisor shall complete the work quantity report submitted by the contractor within 7 days after receiving the work quantity report submitted by the contractor Review
D. The supervisor shall complete the review of the project quantity report submitted by the contractor within 14 days after receiving the project quantity report submitted by the contractor
E. The supervisor shall Complete the review of the quantity report submitted by the contractor within 21 days after receiving the quantity report submitted by the contractor
Correct answer? A, C
55. Quality acceptance of inspection batch Qualification should meet the following requirements
A. The quality of the main control items should be qualified after sampling inspection
B. The visual quality should meet the requirements
C. General The quality of the project has passed the sampling inspection
D. Has complete construction operation basis
E. Quality acceptance record
Correct answer? A, C, D, E
56. Reasons for using automation and robotics in construction projects include.
A. Reduce labor costs
B. Reduce personnel health and safety problems caused by construction projects
C. Competition and cost reduction
D. Characteristics of large quantities and low variety of construction products
E. Guaranteeing the quality of construction projects
Correct answer? A, B, C
57. Related services refer to the service activities provided by the project supervision unit entrusted by the construction unit and in accordance with the construction project supervision contract during the construction project and other stages.
A. Survey
B. Design
C. Construction
D. Warranty
E. Use
Correct answer? A, B, D
58. In post-tensioning construction? The following anchors that are not suitable for single thick steel bars are ( )
< p> A. Screw end rod anchorB. Single hole clip anchor
C. Single taper pin clamp
D. Head anchor Tools
E. Anchors
Correct answer? B, C, D
59. According to the 2013 version of the supervision regulations? The project supervision agency approves the construction unit Expense claims are subject to both the following conditions.
A. The construction unit files a claim for expenses within the time limit stipulated in the construction contract.
B. Is the claim event caused by reasons other than those of the construction unit? And it complies with the construction contract.
C. The claim event is caused by objective reasons and complies with the construction contract.
D. The claim is caused by the construction unit and is in compliance with the construction contract.
E. The claim event caused direct economic losses to the construction unit.
Correct answer?A,B,E
60. Scaffolding must be inspected and accepted at the following stages.
A. After the scaffolding foundation is completed and before the scaffolding body is erected
B. Before loading is applied to the working layer
C. After each erection, 6m to 8m height After
D. After every 10m to 13m height is installed
E. Out of service for more than one month
Correct answer? A, B, C, E< /p>
61. When the normal water level and the highest water level of the groundwater level are both below the basement floor elevation? A vertical moisture-proof layer must be installed on the exterior wall of the basement.
A. Correct
B. Incorrect
Correct answer?A
62. The Lubuge Project adopts internationally competitive Bidding model? ICB)? Open bidding? Select the best world-class contractors within the member countries of the World Bank to undertake project construction tasks.
A. Correct
B. Incorrect
Correct answer?A
63. Does the contractor supply materials and engineering equipment? Contractor The contractor shall notify the contractor in writing 20 days in advance through the supervisor of the arrival of supply materials and engineering equipment. ?
A. Correct
B. Incorrect
Correct answer?B
64. JM12 anchors are used for prestressed steel bars Anchorage of bundles.
A. Correct
B. Incorrect
Correct answer?A
65. Throwing objects from or from buildings If an object falling on a building causes damage to others and it is difficult to identify the specific infringer, unless it can be proved that he is not the infringer, the user of the building who may cause harm will be compensated.
A. Correct
B. Incorrect
Correct answer?A
66. Injury due to collapse of construction projects or engineering facilities In tort litigation for damage, the construction unit and the construction unit shall bear the burden of proof for the damage caused by other responsible persons.
A. Correct
B. Incorrect
The correct answer?A
67. In the original figure? Two line segments Parallel and equal? ??Then the two corresponding line segments in the visual diagram are parallel and equal.
A. Correct
B. Incorrect
Correct answer?A
68. What has passed during the statute of limitations? The right holder’s entity Rights do not disappear because of this.
A. Correct
B. Incorrect
Correct answer?A
69. The north arrow is usually drawn on the general plan and the ground floor plan.
A. Correct
B. Incorrect
Correct answer?A
70. Seismic steel bars should be inspected for general acceptance of concealed steel bar projects Installation status. ?
A. Correct
B. Incorrect
Correct answer?B
71. The data generated by the computer should be based on the content and Signatures are printed. ?
A. Correct
B. Incorrect
Correct answer?B
72. Overdue payment of project advance payment and progress payment The starting point of the statute of limitations shall be the date of payment of the last payment stipulated in the contract.
A. Correct
B. Incorrect
Correct answer?A
73. A cylinder, cone, truncated cone and The three-dimensional view of a simple combination of balls must contain a circle.
A. Correct
B. Incorrect
Correct answer?A
74. In the engineering drawing? Visible in the drawing The line type of the contour line is a thin solid line.
A. Correct
B. Incorrect
Correct answer?B
75. The current building construction regulations stipulate that ordinary clay brick walls The width of the vertical gray joint is 10-12mm.
A. Correct
B. Incorrect
Correct answer? B
76. "Code for Calculation of Building Area of ??Construction Projects"? GB/T 50353-2013 stipulates that the bay window with a height difference between the window sill and the indoor floor is less than 0.45 meters and the net structural height is 2.10 meters or more, 1/2 of the area should be calculated based on the peripheral horizontal area of ??the enclosure structure .
A. Correct
B. Incorrect
The correct answer?A
77. "Code for calculation of construction area of ??construction projects"? GB/T 50353-2013 stipulates that the area of ??a balcony within the main structure is calculated based on the horizontal projected area of ????the structural bottom plate.
A. Correct
B. Incorrect
Correct answer?B
78. The 2013 version of the construction contract model text stipulates claims Expired and invalidated system.
A. Correct
B. Incorrect
Correct answer?A
79. The engineering project department should be established with full-time safety management The safety production responsibility system for managers at all levels is the first responsible person, and it is confirmed by the signature of the responsible person. ?
A. Correct
B. Incorrect
Correct answer?B
80. Flooding refers to the loss of roof waterproofing layer Head area.
A. Correct
B. Incorrect
Correct answer?B
Court-court
Forwards-forwards
Guards-guards
Center-center
Backcourt- backcourt