(a) the general situation of the accident unit;
(2) The time, place and scene of the accident;
(3) A brief description of the accident;
(four) the number of casualties (including the number of people unaccounted for) that have been caused or may be caused by the accident and the preliminary estimated direct economic losses;
(5) Measures already taken;
(6) Other circumstances that should be reported.
The template is as follows:
Xxxx accident report
I. Brief introduction of the accident
Time, place, personnel, gender, department, type of work, accident, injury result
Second, the cause analysis of the accident
1, direct cause (intuitive cause of accident)
1)××××××××××××。
2. Indirect causes (excluding factors other than direct causes)
1)×××××××××××××××××××;
2)×××××××××××××××××××。
3. Main reasons
1)×××××××××××××××××××。
2)×××××××××××××××××××。
Three. Corrective and preventive measures (put forward countermeasures against the above factors)
1)×××××××××××××××××××;
2)×××××××××××××××××××; ?
Fourth, the accident treatment results
1)×××××××××××××××××××;
2)×××××××××××××××××××;
Extended data:
Sample sample:
I. Overview of the accident
On the afternoon of 20xx 13: 15 or so, concrete was poured into the new air compressor seat column in the wind pressure chamber of Sifang Jinshui Copper Smelter, and the connecting cable of the vibrator was electrically contacted. After lunch, the injured Pang Farong prepared for construction. When his hand touched the vibrator connecting cable, he was electrocuted on the spot. At this point, the site construction personnel immediately turn off the power switch.
Pang Farong fell to the ground unconscious at this time, and then the workers immediately carried Pang Farong to the outdoor ground to lie flat, observed his slow heartbeat, and immediately gave him artificial respiration. At the same time, they organized vehicles to send Pang Farong to the hospital for rescue. Two hours after waking up, I was discharged from the hospital for 6 days and went home to recuperate.
Second, the accident analysis
1, through 6: 1 1 electrical contact accident, this accident happened. Although the company conducted safety education for the employees of the construction team, the lack of effective operating procedures and safety inspection and Pang Farong's weak sense of self-protection were the main reasons for the accident.
However, the company has its own defects in safety management. The company is not equipped with designated personnel and full-time electrician technicians to strengthen the supervision and management of safety production operations on the construction site.
2. The quality supervision, quality inspection and safety supervision departments did not send full-time safety officers to the whole construction site for inspection and management, and did not conduct good safety knowledge publicity and education for members of the construction team. The management of the construction site cannot be carried out and implemented.
Safety production technical measures and inspection management are not in place; Failing to understand and convey the development concept of the company's safety production management, as a quality inspection department, failing to take "safety development and prevention first" as the first priority, failing to fulfill the work attitude and responsibility as a quality inspection safety officer, leading to accidents.
3. Project Department: On-site management technicians neglected the details of their usual work, failed to give safety education to team members, failed to follow up and implement their usual work, and failed to seriously deal with the things foreseen in the bud. According to the environmental characteristics of the construction site, they attached great importance to the construction safety production management system ideologically.
4. Team leader: As the team leader of the construction team, safety education is lacking, site management is not in place, safety awareness of construction team members is not strong enough, safety awareness is weak, safety management education for front-line employees is not in place, and all three guarantees are in place.
Three. Summary and requirements
1. Through this accident, it was revealed that managers were careless in their work and had poor safety awareness. It is required to put an end to such incidents in future work.
2, strengthen the safety knowledge consciousness of various functional departments, at the same time, we must strengthen the inspection of the construction site, found that the security risks immediately ruled out.
3. The quality inspection department must often organize employees to learn safety education, and thoroughly explain the operation procedures of construction safety production and the self-prevention consciousness of joint insurance and mutual insurance, and must follow up management.
4, the project leader must always earnestly perform the duty of guardianship at the job site, when the job site is scattered, guardianship is difficult, each job site to add a special guardian.
5, adhere to the people-oriented, carry out safety knowledge education, especially to strengthen the safety responsibility education of the person in charge of the work, and improve the safety awareness and self-protection awareness of employees.
Four. Suggestions for accident treatment:
First responsibility, the Safety Quality Inspection Department failed to supervise and urge the safety work and failed to perform its duties, and fined Yang Fu 600 yuan, Liu 200 yuan, Li Xingmin 200 yuan and Zhou 200 yuan.
Second responsibility: The Project Department failed to supervise the construction site and punished 300 yuan.
Legal Information Network-Regulations on Reporting, Investigation and Handling of Production Safety Accidents