Current location - Quotes Website - Signature design - Do you want to make the wardrobe or blow the putty first?
Do you want to make the wardrobe or blow the putty first?
Pay attention to the order of interior decoration, otherwise it will be very troublesome. For example, the bedroom needs a wardrobe to store clothes, and the walls of the bedroom need putty when decorating. So in the process of bedroom decoration, should we approve putty or install wardrobe first?

First, batch putty or install wardrobe first?

When installing the wardrobe, the wall was blocked by the cabinet, and even if it was painted with putty, it could not be seen. However, it should be noted that a layer of tin foil can be attached to the back of the wardrobe to ensure that the wardrobe will not be damaged by the wet wall.

If the wardrobe is bought in advance, you can put putty on it first. Otherwise it is inevitable that the wardrobe will be dirty during construction.

But if you scrape putty and wall paint first, you can correct the imperfection of the cement wall, because the wardrobes are vertical and you can see clearly a little imperfection, so you should remind the decorator to stick color separation paper and protective film here. It can prevent the wardrobe from being stained by later paint and putty, and the owner should clean it up bit by bit.

Second, the problems that should be paid attention to when installing the wardrobe

1. Before installation, it must be checked. If any abnormality is found, feedback should be given as soon as possible so as to correct it in time.

2. Carefully check the consistency between the drawings and the site, and determine the installation sequence.

3. Pay attention to the protection of product components during installation.

4. Carefully check the beam position, top line and cutting angle of the convergent plate to ensure accurate cutting.

5. Pay attention to the laminated hole surface of the cabinet side plate and try not to put it in the cabinet.

6. When nailing the backboard, measure whether the diagonal lines of the cabinet are equal with a ruler. If the solid layer is uneven, plane it with a plane first, and then nail the backboard.

7. When installing, if the customer raises questions, answer them in time and inform the rationality of the disposal method.

8. If there is any problem in the installation, the installer must fill in the installation notes when returning to the factory and provide follow-up services through the change list.

9. After installation, self-inspection and adjustment must be carried out first, and then the customer will accept and sign for confirmation.

10. After the whole installation service process is completed, we must give our customers a clean environment.

Three, batch of putty should pay attention to the problem

1, select waterproof putty. 82 1 is a putty whose use is restricted by order. It is waterproof, unstable and easy to peel and crack. Many workers often add white latex, 108 glue and other glues to increase the firmness of 82 1, leaving hidden dangers to health. Water resistant putty does not have the above risks. Strong, waterproof, can be used without any glue after adding water, and does not need to be eradicated after long-term use (10-20 years). It is a product that can truly benefit from one construction for a long time.

2. Water-resistant putty should not be scraped too thick in this construction, otherwise it will crack during drying, which is a fly in the ointment. So when the flatness is poor, it needs to be constructed many times, and even the thick bottom is plastered first.

3. When preparing water-resistant putty, it should be prepared according to the ratio of powder: water = 2: 1. Stir with an electric drill first, let it stand for about 10 minutes after it is basically uniform, and then fully stir with an electric drill. Then you can use it.

4. Leveling gypsum: Strictly speaking, leveling gypsum is also a kind of putty, but its main component is gypsum, which has a thick surface and is suitable for leveling with a thick bottom layer. The thickness of one leveling can reach about 5 mm

Good leveling gypsum must be a product with certain water resistance and higher bonding strength than water-resistant putty. Only in this way can we ensure that there will be no problems in long-term use. The construction methods of gypsum and putty are similar, the only difference is that gypsum can be used once, and the drying and curing speed is faster.

5, polish putty. After the water-resistant putty is fully strengthened (5-7 days), it will become extremely strong, and it will become extremely difficult to polish it at this time. Therefore, it is suggested that putty grinding should start 1-2 days after putty scraping. Polishing can be carried out at night, with a bulb of more than 200 watts close to the wall for lighting (also use a bulb for leveling during the day), and check the flatness while polishing.

There will be a lot of dust when polishing putty. Please prepare masks for the people present. Although putty is non-toxic and harmless, dust is not a good thing, so attention should be paid to prevention.

6. Brush the primer. After the floating dust on the polished putty surface is cleaned, it can be primed. Primer can be brushed once, and it must be uniform. After drying (2-4 hours), the next step can be carried out.

Knowing the decoration sequence has a great influence on the construction process. If the order is wrong, sometimes it is too late to remedy it, which will waste a lot of time. If the decoration encounters such problems, remember to communicate with the decoration workers more to make the decoration process smoother.