WINDOWS XP will automatically restart when the system operates improperly or the system crashes. The blue screen is the system's explanation of the reason for the restart and the error. Then the system will automatically run the CHECK tool to correct these problems. Therefore, there is no need to deal with this problem in particular. You only need to pay attention to the operation after recovery. If a blue screen occurs on your computer, it may be caused by both software and hardware. It is not just caused by bad sectors on the hard disk. In terms of software, you can use the latest anti-virus software to scan for viruses. If you have recently installed a new version of the driver, restore it to the original version. If the problem is not solved, you can reinstall the system. In terms of hardware, if you are overclocked, first restore the default frequency of the hardware; then check whether there is a problem with the heat dissipation, because overheating of the hardware will cause data reading and transmission errors; the next step is to use the replacement method to check which component is the problem. Among them, memory is the biggest suspect.
To prevent computer blue screens, you should pay attention to the following points: regularly perform manual backups of important registry files; try to avoid abnormal shutdowns to reduce the loss of important files; for ordinary users, as long as they can run normally, Do not upgrade the BIOS and drivers of the graphics card or motherboard; regularly check and optimize system files, and run the "System File Checker" to check for file loss and verify versions.
◇Solution:
(1) Use the Windows installation CD for repair installation;
(2) If you can still enter safe mode, you can\\" Start --gt; run \\": sfc /scannow
(3) You can also use the method of extracting files to solve the problem. Enter \\"Failure Recovery Console\\" and use the copy or expand command. Copy or decompress the damaged files from the CD. However, the blue screen is usually a problem with the driver file, so the expand command will be used. For example: the blue screen prompts the tdi.sys file, because the driver file is usually in i386\\ driver compressed package, so use: expand CDROM:\\i386\\driver.cab \\f: tdi.sys c:\\winnt\\system\\drivers.(xp is expand CDROM:\\i386\\driver .cab \\f:tdi.sys c:\\windows\\system\\drivers)
If these blue screen stop codes appear during startup
If a blue screen appears during Windows startup , and the error message in Appendix 1 appears, then there is most likely a problem with the hardware. Please use the diagnostic tool provided by the hardware manufacturer to determine whether there is a problem with the hardware, and go to its website to check whether there is the latest BIOS or firmware update program. If There is no problem with the hardware. Reinstall Windows 2K/XP. If the same problem still occurs, you can only seek help from professional technical support.
If you encounter the error message in Appendix 2, you can only reinstall it. After installing Windows, if the problem cannot be solved, it is recommended to seek professional technical support.
1. Fault check information
***STOP 0x0000001E (0xC0000005, 0xFDE38AF9, 0x0000001, 0x7E8B0EB4)
KMODE_EXCEPTION_NOT_HANDLED ***
The first part of the error is the stop code (Stop Code), which is STOP 0x0000001E, which is used to identify the type of error that has occurred. The second part of the error is bracketed The set of four numbers in brackets represents random developer-defined parameters (this parameter is simply incomprehensible to ordinary users, only driver writers or Microsoft operating system developers understand it). The third part is the error name. Information The first line is usually used to identify the driver or device that produced the error. Most of this information is brief, but the stop code can be used as a search term in the Microsoft Knowledge Base and other technical materials.
2. Recommended Operation
The second part of the blue screen is the operation information recommended by the user. Sometimes, the recommended operation is just a general suggestion (for example: go to the seller's website to find BIOS updates, etc.); sometimes, it is also displayed. A tip related to the current problem. Generally speaking, the only suggestion is to restart.
3. The debug port tells the user whether the memory dump image has been written to the disk. Using the memory dump image can determine what happened The nature of the problem will also tell the user whether the debugging information was transmitted to another computer vendor and what port was used to complete the communication. However, the information here is meaningless to ordinary users.
Sometimes the security department can successfully find out which production group has the problem, and will clearly report in the first part which file the error is, but often it can only check the general scope and cannot clearly specify the problem. Because the factory The whole process is forced to stop, and the only way to start is to reorganize and restart. Sometimes, the production team will realize the mistake and will not make it again. But sometimes it will still try to snatch parts, so the factory leader has to repeat
Shutdown decision (unable to start and display a blue screen message, or a blue screen appears again when performing the same operation).
Nine common solutions after a blue screen appears
Windows 2K/XP blue screen message There are too many to fully explain in one article, but their causes often focus on incompatible hardware and drivers, problematic software, viruses, etc. Therefore, we first provide you with some general solutions. When you encounter a blue screen error, you should first check these solutions to eliminate it.
1. Restart
Sometimes it is just a program or driver that makes a mistake temporarily, and they will correct themselves after restarting.( Note: Please refer to 7. Query the shutdown code at this time)
2. New hardware
First of all, you should check whether the new hardware is plugged in securely. This problem that many people ignore often causes many problems. Inexplicable failure. If it is confirmed that there is no problem, unplug it, then try another slot, and install the latest driver. At the same time, you should also check whether the hardware is compatible with the operating system according to the hardware compatibility category on the Microsoft website. If your If the hardware is not in the table, you can check it on the hardware manufacturer's website, or call their consultation hotline.
[color]
Windows XP hardware compatibility list:; 314062
[color] p>
Hardware compatibility category of Windows 2K: /download/display.asp?FileName=hcl/Win2000HCL.txt
3. New drivers and new services
If you have just installed After completing a new driver for a certain hardware, or installing a certain software, which adds corresponding items to the system services (such as anti-virus software, CPU cooling software, firewall software, etc.), a blue screen failure occurs during restarting or use. , please go to safe mode to uninstall or disable them.
4. Check for viruses
Viruses such as shockwave and oscillation sometimes cause Windows blue screen of death, so virus checking is essential . At the same time, some Trojans and spyware can also cause blue screens, so it is best to use relevant tools to scan and check.
5. Check BIOS and hardware compatibility
This often occurs for newly installed computers For blue screen problems, you should check and upgrade the BIOS to the latest version, and at the same time turn off memory-related items, such as caching and mapping. In addition, you should also check your own hardware against Microsoft's hardware compatibility list. Also, if the motherboard BIOS cannot support Large-capacity hard drives can also cause blue screens and need to be upgraded.
QUOTE:
Tips:
BIOS cache and mapping items
Video BIOS Shadowing (video BIOS mapping)
Shadowing address ranges (mapping address columns)
System BIOS Cacheable (system BIOS buffer)
Video BIOS Cacheable (Video BIOS buffer)
Video RAM Cacheable (Video memory buffer)
6. Check the system log
Enter in the Start--gt; menu: EventVwr.msc, press Enter and the "Event Viewer" appears. Pay attention to check the items indicating "Error" in the "System Log\" and "Application Log\". .
7. Query the shutdown code
Write down the dense E-texts in the blue screen, then go online to other computers, enter the Microsoft Help and Support website, click \\ in the upper left corner Enter the shutdown code in "Search (Knowledge Base)\\". If the search results do not find suitable information, you can select \\"English Knowledge Base\\" in the search
Under normal circumstances, you will find useful solutions here. In addition, using the blue screen stop code or the following explanatory text as a keyword search in search engines such as Baidu and Google will often yield unexpected gains.
8. Last known correct configuration
Under normal circumstances, the blue screen appears after updating the hardware driver or adding new hardware and installing its driver. At this time, the \\ provided by Windows 2K/XP "Last Known Good Configuration" is a shortcut to solve the blue screen. Restart the system, press the F8 key when the boot menu appears, the advanced boot options menu will appear, and then select "Last Known Good Configuration".
9. Install the latest system patches and Service Packs
Some blue screens are caused by defects in Windows itself, which can be solved by installing the latest system patches and Service Packs.
Cracking the meaning of classic blue screen cases
Check BIOS and hardware compatibility
For newly installed computers that often have blue screen problems, you should check and upgrade the BIOS to the latest version, and close it at the same time. memory-related items, such as caching and mapping. In addition, you should also check your own hardware against Microsoft's hardware compatibility list. Also, if the motherboard BIOS cannot support large-capacity hard drives, it will also cause a blue screen and needs to be upgraded.
I believe my answer will satisfy you. All the above URLs can be used, just leave them alone. 1． Windows XP has a bug
Windows XP has a shutdown bug. If your computer often displays a blue screen when shutting down, and the fault is intermittent, press the "Ctrl Alt Delete" key. If there is no response, then it is certain that your system has not been patched. Please download the SP1 patch package and patch it, and it will usually be fine.
2. There is a problem with the driver of the innovative sound card
If you are using an innovative sound card and a blue screen appears during the shutdown process with the error code "0X0A", then please enter the device manager, delete the sound card, and refresh , manually install the latest digitally signed driver.
3. Logitech mouse and keyboard are not perfect
If you are using a Logitech network keyboard and have installed the Key Commander software to drive the corresponding network functions of the keyboard, it may cause a shutdown to restart. If the driver of your Logitech mouse is MouseWare8.6, it will cause a blue screen failure during shutdown. You can only solve the problem by uninstalling the driver.
Shut down but cannot automatically cut off the power supply
During the shutdown process, everything is normal, but it stops at "You can safely shut down the computer" but the power cannot be automatically cut off and you need to manually press Press the "Power" button on the main chassis panel to shut down. The reasons for this failure generally include the following aspects:
1. Power support is not turned on
Click "Start → Settings → Control Panel → Power Options → High-Energy Power Management" and check "Enable advanced power management support".
2. Incorrect BIOS settings
It may be that the power management options in the BIOS have been modified by mistake. If you are familiar with BIOS settings, please enter the BIOS and try to modify the power management options in the BIOS. If you are not familiar with the BIOS, simply select the "Load default setup" option to restore the BIOS to the factory default settings.
3. Office XP also causes trouble
Ctfmon.exe in Office XP has always been a controversial issue.
Ctfmon.exe is Microsoft's text service file. As long as the user installs Office XP and installs the "Optional User Input Method Component", this file will automatically call it to provide text for speech recognition, handwriting recognition, keyboard and other user input technologies Input support. Even if we do not start Office XP, Ctfmon.exe is still running in the background. It often causes shutdown failures.
Click "Start → Settings → Control". Panel→Add/Remove Programs", select "Microsoft Office XP Professionain With FrontPage" among the currently installed programs, click the "Change" button, select the "Add or Remove Features" option in the "Maintenance Mode Options" dialog box, click Next, the "Select Installation Options for All Office Applications and Tools" dialog box pops up, expand the "Office Features" option, select the "Chinese Optional User Input Method" option, and select "Do Not Install" in the pop-up menu. , click the "Update" button.
4. APM/NT Legacy Node is not turned on
Under normal circumstances, the APM/NT Legacy Node may shut down but cannot automatically cut off the power. . Enter the device manager and click "View → Show Hidden Devices" in the menu bar to display all hidden devices in the system. Check whether there is an APM/NT Legacy Node option in the device list box. If your computer supports this. function, there will be this option, double-click it, and click the "Enable Device" button in the pop-up properties dialog box.
Windows Blue Screen Error
1 0×00000001 is incorrect. function.
2 0×00000002 The system cannot find the specified file.
3 0×00000003 The system cannot find the specified path.
4 0 ×00000004 The system cannot open the file.
5 0×00000005 Access denied.
6 0×00000006 Invalid code.
7 0×00000007 Storage. The control block is destroyed.
8 0×00000008 There is insufficient storage space to process this command.
9 0×00000009 The storage control block address is invalid.
10 0×0000000A The environment is incorrect.
11 0×0000000B An attempt was made to load a malformed program.
12 0×0000000C Access code error.
13 0×0000000D Data error.
14 0×0000000E There is insufficient storage space to complete this operation.
15 0×0000000F The system cannot find the specified disk drive.
16 0×00000010 The directory cannot be removed.
16 0×00000010 The directory cannot be removed.
17 0×00000011 The system cannot move the file to another disk drive.
18 0×00000012 There is no file.
19 0×00000013 The storage medium is write-protected.
20 0×00000014 The system cannot find the specified device.
21 0×00000015 The device is not ready yet.
22 0×00000016 The device cannot recognize the command.
23 0×00000017 Data error (cyclic redundancy check)
24 0×00000018 The program issued an instruction with the wrong length.
25 0×00000019 The disk drive cannot find the fixed sector or track on the disk.
26 0×0000001A The specified disk or disk cannot be accessed.
27 0×0000001B The disk drive cannot find the requested sector.
28 0×0000001C The printer is out of paper.
29 0×0000001D The system cannot write data to the specified disk drive.
30 0×0000001E The system cannot read the specified device.
31 0×0000001F A device connected to the system has no function.
32 0×00000020 The process cannot access the file because it is being used by another process.
33 0×00000021 Part of the file is locked and cannot be accessed now.
34 0×00000022 The disk drive has an incorrect disk. Please insert 2 (Volume Serial Number: 3) into disk drive 1.
36 0×00000024 There are too many open shared files.
38 0×00000026 End of file reached.
39 0×00000027 The disk is full.
50 0×00000032 This network requirement is not supported.
51 0×00000033 The remote computer is unavailable.
52 0×00000034 The network name is duplicated.
53 0×00000035 The network path cannot be found.
54 0×00000036 The network is busy.
55 0×00000037 The specified network resource or device is no longer available.
56 0×00000038 The network BIOS command limit has been reached. 57 0×00000039 Network adapter card Something went wrong.
58 0×0000003A The specified server cannot perform the requested job.
59 0×0000003B An unexpected network error occurred.
60 0×0000003C The remote patching card is incompatible.
61 0×0000003D The printer queue is full.
62 0×0000003E The server’s space cannot store files waiting to be printed.
63 0×0000003F The file waiting to be printed has been deleted.
64 0×00000040 The specified network name cannot be used.
65 0×00000041 Access to the network is denied.
65 0×00000041 Access to the network is denied.
66 0×00000042 The network resource type is wrong.
67 0×00000043 The network name cannot be found.
68 0×00000044 The name limit of the regional computer network adapter card is exceeded.
69 0×00000045 Network BIOS session limit exceeded.
70 0×00000046 The remote server has been suspended or is starting.
71 0×00000047 Because the number of connections has reached the upper limit, you can no longer connect to this remote computer at this time.
72 0×00000048 The specified printer or disk device has been suspended.
80 0×00000050 The file already exists.
82 0×00000052 Unable to create directory or file.
83 0×00000053 INT 24 failed
84 0×00000054 The storage to handle this request cannot be used.
85 0×00000055 The local device name is already in use.
86 0×00000056 The specified network password is incorrect.
87 0×00000057 Parameter error.
88 0×00000058 A data writing error occurred in the network.
89 0×00000059 The system cannot execute other trips at this time.
100 0×00000064 Unable to create other system semaphore. 101 0×00000065 belongs to the semaphore dedicated to other trips.
102 0×00000066 The semaphore has been set and cannot be closed.
103 0×00000067 Unable to specify semaphore.
104 0×00000068 Unable to request dedicated semaphore at break time.
104 0×00000068 Unable to request dedicated semaphore at break time.
105 0×00000069 The previous ownership of this semaphore has ended.
106 0×0000006A Please insert the disk into 1.
107 0×0000006B The program has stopped because the substitute disk has not been inserted.
108 0×0000006C The disk is in use or locked.
109 0×0000006D Pipe has been aborted.
110 0×0000006E The system cannot open the specified device or file.
111 0×0000006F The file name is too long.
112 0×00000070 Insufficient disk space.
113 0×00000071 No internal file identifier available.
114 0×00000072 The target internal file identifier is incorrect.
117 0×00000075 The IOCTL call performed by the application is incorrect.
118 0×00000076 The write verification parameter value is incorrect.
119 0×00000077 The system does not support the requested command.
120 0×00000078 This function is only valid in Win32 mode.
121 0×00000079 semaphore exceeds the timeout period.
122 0×0000007A The data area transferred to the system call is too small.
123 0×0000007B The file name, directory name, or storage volume label syntax is incorrect.
124 0×0000007C The system call level is incorrect.
125 0×0000007D The disk has no volume label set.
126 0×0000007E The specified module cannot be found.
127 0×0000007F The specified program cannot be found.
128 0×00000080 There are no sub-trips to wait for.
128 0×00000080 There are no sub-trips to wait for.
129 0×00000081 1 This application cannot be executed in Win32 mode.
130 0×00000082 Attempt to use a file handle to an open disk partition for an operation other than raw disk I/O.
131 0×00000083 Attempt to move the file pointer to before the beginning of the file.
132 0×00000084 Unable to set the file pointer on the specified device or file.
133 0×00000085 The JOIN or SUBST instruction cannot be used with disk drives that contain previously joined disk drives.
134 0×00000086 Attempt to use JOIN or SUBST instructions on disk drives that have been joined.
135 0×00000087 Try using the JOIN or SUBST instruction on the replaced disk drive.
136 0×00000088 The system attempts to delete the link relationship of an unlinked disk drive.
137 0×00000089 The system attempts to delete the replacement relationship of the disk drive that has not been replaced.
138 0×0000008A The system attempted to combine the disk drive to the directory of the disk drive that has already been combined.
139 0×0000008B The system attempts to replace the disk drive with the directory of the disk drive that has been replaced.
140 0×0000008C The system attempts to replace the disk drive with the directory of the disk drive that has been replaced.
141 0×000000 The system attempts to SUBST the disk drive into a combined disk drive directory.
142 0×0000008E The system cannot execute JOIN or SUBST at this time.
143 0×0000008F The system cannot combine disk drives or replace directories under the same disk drive.
144 0×00000090 This directory is not a subdirectory of the root directory.
145 0×00000091 There is still data in the directory.
146 0×00000092 The specified path has been replaced.
147 0×00000093 Insufficient resources to process this command.
148 0×00000094 The specified path cannot be used at this time.
148 0×00000094 The specified path cannot be used at this time.
149 0×00000095 The disk drive directory being attempted to be combined or replaced is an already replaced target.
150 0×00000096 The CONFIG.SYS file does not specify system tracing information, or the tracing function is canceled.
151 0×00000097 The number of specified semaphore events DosMuxSemWait is incorrect.
152 0×00000098 DosMuxSemWait is not executed; too many semaphore are set.
153 0×00000099 DosMuxSemWait manifest is incorrect.
154 0×0000009A The storage media identifier you entered has a length limit.
155 0×0000009B Unable to create other execution threads.
156 0×0000009C The receiving trip refused to accept the signal.
157 0×0000009D The section has been abandoned and cannot be locked.
158 0×0000009E The section has been unlocked.
159 0×0000009F The address of the thread identifier is incorrect.
160 0×000000A0 The argument string passed to DosExecPgm is incorrect.
161 0×000000A1 The specified path is incorrect.
162 0×000000A2 signal is waiting for processing.
164 0×000000A4 The system cannot create an execution thread.
167 0×000000A7 Unable to lock part of the file.
170 0×000000AA The requested resource is in use.
173 0×000000AD The locking requirement for canceling the range is not obvious.
174 0×000000AE The file system does not support automatic change of lock type.
180 0×000000B4 The system found an incorrect section number.
182 0×000000B6 The operating system cannot execute 1.
182 0×000000B6 The operating system cannot execute 1.
183 0×000000B7 The file already exists and the same file cannot be created.
186 0×000000BA The transmitted flag is wrong.
187 0×000000BB The specified system flag cannot be found.
188 0×000000BC The operating system cannot execute 1.
189 0×000000BD The operating system cannot execute 1.
190 0×000000BE The operating system cannot execute 1.
191 0×000000BF Unable to execute 1 in Win32 mode.
192 0×000000C0 The operating system cannot execute 1.
193 0×000000C1 1 is not a correct Win32 application.
194 0×000000C2 The operating system cannot execute 1.
195 0×000000C3 The operating system cannot execute 1.
196 0×000000C4 The operating system cannot execute this application.
197 0×000000C5 The operating system is currently unable to execute this application.
198 0×000000C6 The operating system cannot execute 1.
199 0×000000C7 The operating system cannot execute this application.
200 0×000000C8 The program code section cannot be larger than or equal to 64KB.
201 0×000000C9 The operating system cannot execute 1.
202 0×000000CA The operating system cannot execute 1.
203 0×000000CB The system cannot find the entered environment option.
\r
205 0×000000CD In the command subdirectory, no process has a signal sub-handler.
206 0×000000CE The file name or extension is too long.
207 0×000000CF ring 2 stack is in use.
207 0×000000CF ring 2 stack is in use.
208 0×000000D0 The entered universal file name element * or ? is incorrect, or too many universal file name elements are specified.
209 0×000000D1 The signal transmitted is incorrect.
210 0×000000D2 The signal processing program cannot be set.
212 0×000000D4 The section is locked and cannot be reconfigured.
214 0×000000D6 There are too many dynamic link modules attached to this program or dynamic link module.
215 0×000000D7 Can't nest calls to LoadModule.
230 0×000000E6 The pipe state is invalid.
231 0×000000E7 All pipes instances are busy.
232 0×000000E8 The pipe is being closed.
233 0×000000E9 No process is on the other end of the pipe.
234 0×000000EA There is more information available.
240 0×000000F0 The job phase was cancelled.
254 0×000000FE The specified extended attribute name is invalid.
255 0×000000FF The extended attributes are inconsistent.
259 0×00000103 No data available.
266 0×0000010A Unable to use Copy API.
267 0×0000010B The directory name is wrong.
275 0×00000113 The extended attribute does not apply to the buffer.
276 0×00000114 The extended attribute file on the plug-in file system has been damaged.
277 0×00000115 The extended attribute table file is full.
278 0×00000116 The specified extended attribute code is invalid.
278 0×00000116 The specified extended attribute code is invalid.
282 0×0000011A The plug-in file system does not support extended attributes.
288 0×00000120 Intention to release a mutex that does not belong to the caller.
298 0×0000012A semaphore The number of transmissions is too many.
299 0×0000012B Only partially completes the requirements of Read/WriteProcessMemory.
317 0×0000013D The system cannot find the message numbered 0×00001 located in message file 2.