Xiaomi 2S/2 Universal Partition Course!
Tell the truth first. I changed the partition three times:
Preparation materials: a 20CM wire, lighter, transparent adhesive, preferably original data cable, battery with at least 50% power, computer that can brush the wire normally, toothpick (what's the use? You'd better have a helper.
Premise: Your computer can brush your Xiaomi 2 or 2S normally! What other millet assistants are there? Mishan, I won't say much about this.
Start work:
0: In the control panel, find the settings as shown in the figure.
Then click "Device Installation Settings". Pick the second one! It is best to ensure the smooth flow of the whole network!
1: Restart the computer, and press F8 all the time when it is turned on to enter the safe selection mode, as shown in the figure, select "Disable driver signature enforcement" and confirm.
Wait for it to open completely. It is best to start running CMD again and enter the following command bcdedit/set testsigning on. In fact, this command is "Disable driver signature enforcement". Do it again now just in case!
2. Make short-circuit wires. According to my picture: it's a bit like the Y line of WP7 jailbreak. (Hehehe, did you see the test paper below? Hehe, I am a people's teacher.
3. Open the device manager of the computer.
4. Download the latest corresponding line brush package, address: /download.asp, and download the corresponding version of your computer system.
Open it.
7: Insert the lowest end of Y line into the negative pole of battery contact point, and be careful not to jump to the next contact point. Use a toothpick at this time to avoid touching the line at the second contact point! Done, stick it with transparent glue, and the effect is as shown in the figure.
8: Don't connect the data cable to the mobile phone. Plug the other end of the data cable into the computer first! When brushing the computer, it is best to plug in what interface (to prevent the driver from installing incorrectly), and it is strongly recommended to use the socket at the back of the chassis on the desktop.
9. Make the following gestures: Hold on, make sure the short circuit is good, and don't move! If you can, please ask your classmates or people next to you to plug in the end of the data cable that is not plugged into the mobile phone.
10: Put the window of the device manager in front and wait for the response from the device manager opened by the computer! As shown in the figure: Be careful not to let go at this time!
COM 10 will be prompted when installing the driver (this number is uncertain and will be automatically assigned according to your computer).
If the device manager doesn't respond, please disconnect the plug from the computer and try again. Make sure the short circuit is good. I'll do it all at once. )
1 1: You'd better wait for the driver to be installed before loosening the shorted wire! At the same time, remove the Y line. But make sure the data cable is not unplugged!
12: Install the battery. Make sure the battery is fully charged.
13: Return to the Open Line Brush tool and click Refresh. COM 10 will appear. Then you turn on the brush machine. At this time, make sure that the settings of miflash are the same as I said before. If it's different, you'd better modify it. Press the picture above me!
14: During the brushing process, the driver needs to be installed automatically. Please wait for the automatic installation. When the driver is installed again, the COM port will change, usually by adding a value. Change it to COM 1 1, as shown in the figure:
15: While waiting for the brush, the installation partition of Xiaomi 2S has been identified in the opened DiskGenius software. As shown in the figure. But don't go to DiskGenius at this time. It doesn't matter.
16: Return to the brush window. It takes a long time to brush a machine of this depth. But I tried it twice, both in about 500S, remember to wait until the brushing machine is completely completed! Be sure to wait for the prompt: "Operation completed!"
17: The most critical action: Although the brush prompt is successful, don't unplug the data cable in a hurry! Otherwise, the above operations are all done in vain.
18: Return to the open DiskGenius window. In order to prevent operational errors, it is better to back up the partition table of Xiaomi mobile phone itself. Click the mouse on the disk of the mobile phone first and select it. Back up the partition table on the hard disk above the software. No matter where you back up. Only you remember. And it is recommended to keep this backup.
19: Follow the diagram step by step. The mouse selects the partition 25 displayed on the left side of the software! This partition is system storage! Originally, Xiaomi defaulted to 3.75GB. I don't know why this software shows 3.5GB, and partition 26 is the storage capacity of SD card. All we have to do is operate these two partitions.
The idea is to reduce the storage capacity of the system and increase the storage capacity of the SD card. Partition 26 is hidden and not displayed, but your mouse will also have a right-click menu in the space behind partition 25. )
20: As shown in the figure, delete partition 25.
2 1: Note that partition 25 has been deleted. It is on the left side of the software. Partition 25? This is not a software error. This partition 25 is changed from the original partition 26. Again, we continue to delete.
22: After deletion, the following is the problem of creating a partition: right-click the deleted blank to create a new partition. Look at the picture. Look at pictures more clearly than words. Note: It is suggested that the system storage should be no less than 1024MB, that is, 1GB, especially for those players who have installed many large games, at least 1.8gb. How many points should you calculate? I don't need to teach this, do I?
23: Create partition 25, and then create partition 26. Similarly, right-click the blank space and create a new partition table. Look at the picture: Look at the picture more clearly than the text.
24: The partition is completed here, and then the changes are saved, prompting whether to save the changes.
Prompt whether to format, the key is.
Note: You will be prompted whether to save the boot record. Points reservation. If there is no reservation, you can refresh the machine and generate a boot to make it start smoothly.
25: Last step: Select the location of partition 25. Hide it because it is hidden (see the picture in step 19 for details). Save the changes again.
26: At this point, close the DiskGenius software. Disconnect the data cable. It is recommended to unplug the battery before plugging it in. Open it. At this time, if the boot is successful, enter the set storage area to see if the change is successful. If it doesn't work, try again.
27: It is suggested that after successfully entering the system, there should be backup and reset in the settings. Reset, select format memory card and delete all user data.
28: This is the end of the tutorial. Surgery is risky. Please think twice before operation. I'm irresponsible. What's the problem?