What is a decoration safety agreement and a model decoration safety agreement?
Party A: (hereinafter referred to as Party A)
Party B: (hereinafter referred to as Party B)
According to the requirements of relevant national safety laws and regulations, combined with the actual situation of our company, we will conscientiously implement the "6 1" instruction, implement the policy of "safety first, prevention first" and the principles of "who is in charge, who is responsible" and "safety must be paid attention to in production", and implement the safety responsibility system. In order to ensure construction safety and prevent accidents, Party A and Party B must perform the following clauses:
1. Party A shall fully cooperate with the security work of this project, supervise and inspect the security work of Party B at the same time, and have the right to require Party B to rectify the violations, illegal acts and potential safety hazards found in the inspection.
2. Party A shall, according to the requirements of the company, notify Party B of the problems found in the inspection in writing and file them for future reference.
3. Party A has the right to punish Party B's "three violations" according to relevant management measures.
4. If Party A neglects the safety management of decoration engineering, it shall report to the company's security department in time.
5. Party B must have a clear legal person in charge of safety, who is responsible for the safety and public order of the construction project, so as to achieve "five simultaneities" of construction and safety.
6. Before entering the construction site, Party B must register and pass for the construction personnel, and designate a special person to do the inspection. Unlicensed persons are not allowed to enter the construction site.
7. Before Party B takes up his post, he must be responsible for the safety education of construction personnel, make clear the relevant safety regulations and work requirements, and consciously abide by the safety management system.
8. Party B must be equipped with full-time or part-time security personnel during the construction period, specifically responsible for the implementation of safety and public security precautions during the construction period.
9. The inflammable, explosive and dangerous goods used by Party B in the construction must be restricted, and a special person shall be appointed to take charge of safety management.
10. When Party B uses fire, electricity and welding in the construction, it must be approved by the person in charge of Party B's site, and strictly implement the technical specifications and operating procedures of fire, electricity and welding to ensure foolproof. (Oxygen cylinders and acetylene cylinders shall not be inverted, with damping rings, and their number shall be strictly controlled. The spacing is greater than 5m, and the distance between the open flame and the acetylene bottle must be greater than 10m. There is a special person to remove flammable materials, put a fire extinguisher on site, leave a special person on duty after welding, and leave after confirming that there is no problem)
1 1. Party B's electricians and electric (gas) welders must hold a valid Operation Certificate for Special Industry Personnel issued by the labor department before they can operate according to the requirements of construction site specifications.
12. Party B must carry out the construction in strict accordance with the national safety construction standards for building decoration industry and resolutely put an end to "three violations".
13. When Party B uses large-scale equipment in construction, it must fully consider the bearing capacity and seismic capacity of the floor, and can only use it on the premise of ensuring safety. It is strictly forbidden to command and take risks in violation of regulations.
14. Party B must set up a safety net for dangerous holes (access openings, elevator openings, reserved openings, stairs, etc.). ) construction, and fasten the safety rope for aerial work.
15. Smoking, using naked flames, leaving behind construction workers and using electric water heaters are strictly prohibited in the decoration area.
16, it is forbidden to pile up a large amount of waste for a long time in the construction area, block the evacuation passage, and insist on cleaning it up once a day, especially the empty bottles such as glass glue and paint should be properly handled.
17. Party B must strictly manage the construction site, and the equipment, equipment, tools and materials on the construction site must be managed by special personnel.
18. Party B must equip the construction site with fire-fighting equipment that meets the specifications and standards to ensure the safety of the whole construction process.
19. If Party B neglects safety management or violates the provisions of the contract, resulting in accidents and cases, Party B shall bear all the responsibilities, and all the economic losses and political impacts brought to Party A therefrom shall be borne by Party B. ..
20. This responsibility shall come into effect as of the date of signing, and shall become invalid after the project is accepted, in duplicate, one for the owner and one for the construction unit.
Party A: Signature of Representative: Year Month Day
Party B: signature of representative: signature of project supervisor: year month day.
The model decoration construction safety agreement is as above. The safety agreement needs to be signed by both parties before the start of construction, and the construction party will perform the safety agreement, and there will be an agreement to safeguard rights in the future.
The above is a detailed answer to what is the decoration safety agreement and the demonstration decoration safety agreement. I wonder if you are satisfied with our introduction.