Company site management regulations
In order to improve production order and working environment, strengthen production safety, make site management (5S management) meet the requirements of clean environment, clear area and strict discipline, and realize civilized production of modern enterprises, the company has formulated site management regulations.
I. Detailed Rules for Comprehensive Management of the Company's Site
1, various identification requirements:
1. 1 Warning signs, safety production and civilized production publicity signs shall be clear and correct, free from damage and pollution.
1.2 All pits, ditches and ditches shall be surrounded by guardrails or cover plates (generally, guardrails shall be no less than 1050 mm, and cover plates shall be fixed). During maintenance, the construction unit has the responsibility to restore the removed guard plate or cover plate to its original position after the construction.
1.3 The health responsibility area in the company is clear, and the responsibility signs are complete, eye-catching and undamaged.
1.4 All kinds of publicity placards and celebration flags are hung neatly and beautifully, and outdated slogans and notices must be removed in time.
1.5 The interior wall of the company is intact, with good lighting at night.
2. Internal roads of the company:
2. 1 roads in the company should be unblocked at any time, and there should be obvious parking areas on the roads, and the signs should be
Eye-catching In principle, vehicles parked in the divided area will have their heads facing the gate of Gonggong Company.
2.2 Production operations shall not occupy roads, and vehicles shall not block roads. Transport vehicles should be removed and parked in the designated parking area after unloading in the reservoir area or workshop.
2.3 Without approval, foreign vehicles such as taxis, motorcycles, three-wheeled trucks and tractors are not allowed to enter the production area. These vehicles should be parked in designated parking areas.
2.4 bicycles are not allowed to be parked in the production area (including roads), and bicycles should be parked in a unified bicycle shed.
2.5 Raw materials, materials, waste materials and building materials shall not occupy the regional roads of the company, and short-term stacking shall be approved by the person in charge of the office.
2.6 Semi-finished products and finished products shall be neatly placed in the specified area and position, and shall not exceed the divided area, and there shall be no sundries and garbage around.
3. Hygiene in the company area:
3. 1 put an end to smoking and littering cigarette butts in the company area.
3.2 Garbage bins and waste bins should be located and set up, unobstructed, and cleaned up in time.
3.3 There shall be no sundries and flower beds in the green area, and there shall be no architectural relics and other wastes in the flower beds.
3.4 There is no phenomenon of drying clothes in the company area.
3.5 The setting of fire fighting equipment shall comply with relevant regulations, with no obstacles around, and comply with relevant fire fighting laws and regulations.
3.6 After the completion of all kinds of construction and renovation projects, the site must be cleared and the original site management requirements must be restored.
Second, the workshop site comprehensive management rules
1, various signs in the workshop:
1. 1 All kinds of warning signs, fixed management signs, safety production and civilized publicity signs are obvious, neat, free from damage and pollution.
1.2 There should be guardrails or cover plates around pits, pools and ditches in the workshop. The height of guardrail shall be no less than 1050 mm, and the cover plate shall be fixed. (If pits and ditches must be set in the production process, guardrails and cover plates cannot be added, and there should be obvious and eye-catching warning signs around them).
1.3 the corner of guardrail and equipment shall be marked with safety signs, and the color shall be eye-catching and in line with relevant state regulations.
1.4 channel signs and article positioning lines shall be eye-catching and the colors shall conform to the regulations.
2. Roads in the workshop
2. 1 Articles, parked vehicles and small mobile equipment are not allowed in the passage, and there are no ditches, grooves, protrusions and stagnant water on the road surface.
2.2 On the road in the workshop, vehicles should be removed as soon as possible after unloading, and no empty parking or occupation of the road is allowed.
3. Stacking of materials and products:
3. 1 The arrangement of work-in-process and material accessories shall be consistent with the layout plan required by the process, and there shall be a fixed line division.
3.2 Work-in-process and material accessories shall be placed with corresponding appliances in a fixed position, and the stacking height shall not exceed 1500mm.
3.3 The height of articles that cannot be put on shelves or stacked without utensils (except those with protective measures) shall not exceed 1200mm. It shall not be placed directly on the ground, and there shall be an effective partition between articles and the ground.
4. The articles at each station in the workshop are stacked as follows:
4. 1 The stacking amount of materials in the work area of each workshop is the output of that day.
4.2 Valuables are transported with the vehicle and are not stacked in the workshop.
4.3 The raw materials, materials and auxiliary materials in the workshop should be given priority in advance without special circumstances.
5, workshop production site:
5. 1 The production site should be clean and tidy, and always keep "four noes" (no garbage, no sundries, no oil and water, no cigarette butts).
5.2 The "four unused" materials in the production site are often cleaned up, especially during the product model replacement period, and the cleaned items are handed over to the warehouse for other purposes (mainly redundant, eliminated, changed models and not used for a long time).
5.3 In principle, packing boxes, boxes and bags of various articles shall not be opened or discarded in the workshop, and shall be cleaned up in time.
5.4 Smoking spots should be set at proper positions in the workshop, and smoking is strictly prohibited in other areas.
6, equipment and auxiliary workspace:
6. 1 The appearance maintenance of all kinds of equipment should be "three noes" (no oil stain, no yellow spots and no rust).
6.2 Workstation appliances and toolboxes shall be neatly arranged.
6.3 The prescribed smoking spots should be clean and tidy, with wet cigarette butts, and no cigarette butts on the ground.
7, workshop office and locker room:
7. 1 Workshop offices and changing rooms should be kept clean and tidy.
7.2 The locker room should be "four noes". Don't throw away clothes, shoes, sundries, garbage and cigarette butts.
7.3 It is forbidden to pour face washing water and foot washing water into the dressing room.
8. Company office:
8. 1 The office of the company should be kept clean and tidy, and items such as desks should be placed according to the fixed management layout.
8.2 Tea sets for reception in the business department shall be cleaned, disinfected and put in order.
8.3 All kinds of documents and materials shall be delivered, placed neatly and clearly classified.
8.4 Surface of office equipment (computers, photocopiers, etc.). ) should be clean and dust-free.
8.5 Various charts and post standards shall be hung on the wall without damage.
8.6 The office is basically "three noes" (no cobwebs, dust and cigarette butts on the ground).
Three, warehouse (intermediate library, tool library, etc ... ) website management rules.
1, logo and number:
1. 1 The warehouse must have a number and indicate the contents of the goods.
1.2 Material placement (stacking) is consistent with the plane setting.
1.3 materials shall be placed in areas, frames, levels and positions with complete marks.
2. Channel:
2. 1 The material warehouse passage must be unblocked.
2.2 The channel setting in the warehouse should be the same as the Detailed Rules for Comprehensive Management of Workshop Site.
3.WIP and material placement:
3. 1 The storage method of materials shall comply with the relevant provisions of material management:
3.2 For materials fixed in areas, frames, floors and positions, partitions shall be placed for materials that cannot be put on shelves.
3.3 Materials can be stacked in layers in 32 1.
3.4 Scrapped, sluggish and off-balance-sheet materials shall be clearly identified, classified and piled up, and treated regularly.
3.5 Items shall not be placed on the corresponding vertical plane around the distribution board and fire control facilities.
4. Venue
4. 1 The reservoir area is clean with "four noes" (no dust, garbage, cobwebs and stagnant water).
4.2 No clothes are allowed to dry in the reservoir area, and there is no sanitary corner.
4.3 Warning signs in the dangerous goods warehouse shall be eye-catching, fireworks are strictly prohibited, and fire control facilities shall be in good condition.
4.4 Lifting tools shall have a fixed storage area and shall not be placed at will.