How to select a printer port
Taking G-3 106 as an example, other models of machines choose serial port or USB port.
(1) Click Desktop Start → Control Panel → Printers and Faxes to open the following window. (as shown in figure 1)
(Figure 1)
(2) Select G-3 106 printer, right-click and select Properties (as shown in Figure 2).
(Figure 2)
(3) Click "Port" in the properties dialog box, for example, select "LPT 1: printer port". Click OK to complete the port selection. As shown in fig. 3)
Figure (3)
Tip:
Usually, the port number of the parallel port integrated in the computer motherboard is LPT 1. If the parallel port is added by an additional parallel card, LPT3 or LPT2 should be selected.
If you use a USB cable, you need to select the corresponding USB port. At the same time, every time you install the system, you will automatically create a USB port, such as USB00 1, USB002, etc. , one-to-one correspondence with USB ports on the computer.
Question 2: How to choose the print port for printer installation? Different brands of large printers will have different settings. Right-click the printer and select printer properties-there are LPT 1, LPT2 and LPT3 in the ports. These three ports are for USB (there is only one printer installed on your computer, which is LPT 1). In addition, see if the printer is connected when the computer is turned on. If so, just turn off the computer and turn it on before connecting the printer.
Question 3: When installing a printer, how to choose a printer port generally does not need to choose a print port. Just install the printer's own driver, and always install it by default. Traditional printers can choose any LTP port, and USB does not need to choose a port at all. Setup will automatically open the corresponding port.
Question 4: How to set the printer port? You need to download the printer driver of HP 1020 to install, and other driver software cannot be installed. . . When installing the port, you can choose. . There is generally no problem by default. You can look at the port number of Epson first. If it is USB 1, just set HP 1020 to USB2.
Question 5: How to view the printer port The printer port can be viewed as follows:
1. Enter Control Panel-Devices and Printers;
2. Right-click the printer you want to view and select "Properties"; 3. Select "Web Service" to view the IP port.
Question 6: How to set the printer port How to set the port:
Go to Control Panel-Printers and Faxes-Right-click the printer icon-Properties-Ports, and select Use.
lpt port
Use parallel lines, use USB transmission lines, and select USB ports.
, select LPT 1 port.
Using the serial port, select the port 1.
Question 7: When the printer is installed, the port is selected at 20 o'clock, and the LTP port is not a serial port, but a parallel port. A serial port is a kind of port. What port can be selected first, mainly depends on whether the motherboard has this port. If yes, there is a choice of this port, and the printer should also have this port. Changsha Gao Qiao New World Technology, professional printer maintenance.
Question 8: How to set the printer port in the BIOS and click the DEL key on the keyboard to enter the computer BIOS? The steps are: advanced-onboard equipment configuration-parallel port address [278]- parallel port mode -EPP+ECP, and some numerical control equipment is also acceptable. Numerical control can also be changed to Epp or Ecp debugging.
Question 9: How to set the port 1 for the printer connected by the network cable? Connect the printer to the port of the switch (router) with a network cable, and use the control panel that comes with the printer to change the default IP of the printer to the IP address in the LAN (or automatically match, supported by HP). Repeat this step to see the specific IP address that matches). Be careful not to conflict with the IP address of any device in the network.
2。 Open the printer window. Double-click the "Add Printer" icon to pop up the wizard dialog box.
According to the system prompt, click the Next button to pop up the dialog box. At this point, select the "Local Printer" button. Do not check Automatic Detection.
3。 On the second page, select the Create New Port button and select the Standard TCP/IP Port option from the drop-down list box. Click Next to pop up the wizard dialog box for adding TCP/IP printer ports. Fill in the IP address just set or automatically matched. The port name can be written at will.
4。 Install the printer driver according to the prompts (most HP XP systems have their own drivers, just choose from the list).
If a prompt pops up asking whether the printer is * * *, choose a different share, because this is a point-to-point connection and * * * is not needed. Next is the routine work such as printing test pages.
Question 10: How to select LPT 1 for the printer port? The machine of L800 uses USB cable, so you can choose USB when choosing the port.