Cut off the cat's power?
Unplug the phone line?
Plug in a USB storage device?
Turn on the cat's power and be careful not to answer the phone line?
Turn on the computer, plug in the network cable, and wait for the cat to start refreshing the configuration?
Open management in a browser?
Enter the password nE7jA%5m?
Click Network → Remote Management?
Note: Not available?
ACS URL: Change this address so that the telecom can't connect you, such as /acs, but remember the original ACS URL.
Change the ACS user name at will, don't touch the ACS password, but remember the original user name?
Select the connection request to verify that it is valid, and make sure to select it?
Don't default to the connection request user name, just change it so that the telecom can't connect you, for example, change it to howhfofjwoafe, but please remember the original user name?
Remember to click Save/Apply to save the settings?
Click Manage → User Management to modify the password of useradmin. Please remember this password?
Click Manage → Device Management. Remember to unplug the USB storage device at this time?
Click Save/Restart to restart cat to make the previous settings take effect. Please wait patiently for a few minutes and remember to unplug the USB storage device, or go back?
Reset ADSL network connection
Log in with the previous telecomadmin after restarting?
Click Network → Broadband Settings?
Follow the following settings?
Connection name: Create a new connection?
Connection mode: routing?
Choose PPPoE?
Select NAT as valid?
Please consult your ADSL service provider for VPI and VCI, because different regions are different?
Service category: UBR without PCR?
Invalid option to enable VLAN?
VLAN ID: It's blank, isn't it?
Packaging: LLC/ Snap-on Bridge?
User name and password fill in your ADSL account number and password?
Service name:?
Select enable 802. 1p queue as invalid priority?
Service Class Binding: Normal?
Choosing LAN 1, LAN3, LAN4, wireless 1 is effective. Be careful not to choose LAN2 because it is the port of IPTV digital TV?
Click OK?
Wireless network settings
Click network →WLAN configuration?
Select Enable Wireless as Active?
SSID: Any name, that is, the name you see when the computer is connected, and then fill in the default settings such as password?
Click OK?
Turn electric donkey into HighID (using NAT virtual server)
Click Apply → Advanced NAT Settings?
Click Add? under Virtual Host Settings.
Pop up another page and click Add?
The server selects the client server, and the text box has a name, such as P2P?
Fill in your own intranet address for the server IP address, such as192.168.438+0.438+000?
The following table is to fill in the external start port, external end port protocol, internal start port, internal end port and remote IP remote port as follows.
xxxx xxxx TCP xxxx xxxx
yyyy yyyy UDP yyyy yyyy
Where xxxx is the TCP port number of the electric donkey and yyyy is the UDP port number of the electric donkey. You can write it according to the settings of the electric donkey, and then click Save/Apply at the bottom of the table.
Click Apply →UPNP Configuration?
Select Enable UPNP as valid?
Click OK?
Then you must restart the cat for the settings to take effect!
Turn the electric donkey into HighID (using DMZ)
Click Security → Firewall?
Set the firewall to off?
Click Apply → Advanced NAT Settings?
Select Enable DMZ as valid?
Does the host IP address of DMZ depend on your computer's intranet address?
Click Save/Apply?
Click Apply →UPNP Configuration?
Select Enable UPNP as valid?
Click OK?
Then you must restart the cat for the settings to take effect! ?
Restore IPTV
If you find that you can't connect to IPTV after configuring the route, please restore the remote management function to its original state, that is, the ACS URL, ACS username and connection request username are all restored to their original values, but you may not be able to log in with telecomadmin next time, but it doesn't matter. As long as the route is modified this time, there should be no need to move in the future. If this is a big problem, you should try again with a USB storage device.