Asus, after installing win7 using Chinese cabbage, it has been restarting repeatedly
It is recommended that you change a system image file and try the installation. The process of installing the system from Chinese USB disk:
1. Use the Dabaicai U disk boot disk creation tool to make a bootable U disk;
2. Download a GHOST system image;
3. Set the USB boot disk in the BIOS Start the disk and put the previously downloaded image into the U disk;
4. After the U disk starts, select an item similar to "GHOST Manual Installation" on the startup interface. After entering, select the installation source for you. For systems placed on a USB flash drive, the installation path is your C drive. Or select PE in the interface, and then there is a one-click installation software in PE (just on the desktop), select the image you put in U, and install it on your C drive. A progress window will appear at this time and restart after completion.
5. Remove the U disk after restarting, and then the machine will automatically install itself. Just click "Next" or "OK" until the installation is completed
Chinese cabbage u Boot disk creation tool: bigbaicai. Asus laptop win8 system cannot be restarted after installing win7 with Chinese cabbage
You cannot use GHOST system when replacing WIN8 with WIN7, you must use a pure version. Go online and download a pure version of WIN7 image file or buy a pure version of WIN7 CD, format the entire disk and repartition it, and then install the system. After it is installed, enter WIN7 and download a driver wizard with a network card in advance. After installing the network card, Use the driver wizard to install other drivers online! Then download the software you need! Then surf the Internet with peace of mind! Asus k550j Dabaicai cannot boot after installing win7
If the system installation fails, just change to a win7 system disk with good compatibility to boot the computer, and continue to reinstall the win7 system, so that the win7 process can be solved automatically and smoothly The system installation failed and the desktop cannot be accessed. You can use a USB flash drive or hard disk, and the installation speed is very fast. But the key is: there must be a system disk with good compatibility (compatible with ide, achi, and Raid mode installation) and can be automatically and permanently activated, and can automatically install the machine hardware driver, so that the system can be reinstalled automatically and smoothly. . The method is as follows:
1. U disk installation: Use ultraiso software to open the downloaded system installation disk file (ISO file), execute "Write Image File", insert the U disk into the computer, and click " OK", wait for the program to be executed, and then the USB disk for starting and installing the system is ready. After booting the machine with this prepared system USB disk, the system can be reinstalled smoothly;
2. Hard disk installation: The premise is that there needs to be a Windows system that can run normally. Extract "*.GHO" and "Install System.EXE" in the downloaded ISO file to the non-system partition of the computer, and then run "Install System" .EXE", press Enter directly to confirm the restore operation, and confirm again to execute the automatic installation operation (make sure to back up important data on the C drive before execution);
3. Graphic tutorial: There is a detailed graphic version in this regard How can I give you an installation tutorial? Cannot be attached. It will be judged as a violation by the system.
This can solve the problem. The download address of the system disk for reinstalling the system is in the upper right corner of the "Know Page"... si xin zhong... Yes! Hope to adopt! Asus laptop win8 system cannot be restarted after installing it with Chinese cabbage
The computer cannot be started,
I usually check like this
I don’t know now Where is the specific problem? If there is no alarm sound, then consider the simplest problem first
For example, the memory module is loose, or the motherboard cannot recognize the memory due to oxidation of the gold finger. At this time, remove the memory module. Unplug it, wipe it clean and then plug it in again
Start the computer, usually this will solve the problem
If it still doesn't work, if you have an independent graphics card, also unplug it and wipe the gold finger. If The motherboard has an integrated VGA interface. You can use the motherboard's graphics card interface. After determining the problem, plug in the graphics card.
If the problem cannot be solved after wiping the memory and graphics card, don't panic. You can replace the motherboard Remove the s battery from the mountain, cut off the power, wait a few minutes and then reinstall it
Sometimes the s configuration changes due to hardware changes may also cause the computer to fail to boot
If these If it doesn't work, you need to consider the motherboard or CPU problem
If there is a CPU problem, first check whether the power supply is normal
There are two situations when the computer cannot enter the system when it is turned on: the self-test fails. There is a hardware problem. If you can pass the self-test but cannot enter the desktop, it is a system or driver problem.
1. If you can pass the self-test but cannot enter the desktop, it is a problem with the operating system or driver:
Why does the computer fail to enter the desktop normally after repeated restarts or has a blue screen of death?
When excluding viruses, it is usually because the GHOST version or other modified versions of the operating system are installed, because in advance A large number of integrated drivers that are not suitable for your hardware device cause the system to be unable to correctly identify and load the hardware devices necessary for the system.
Re-download and install the original image installation version of the operating system and install all the drivers. Drivers with Microsoft WHQL certification can correct such errors.
If you don’t want to reinstall, try booting F8 into safe mode to uninstall the incompatible driver of the hardware device (that is, right-click the driver in the device manager) Device)>Properties>Driver does not have a driver with >Digital Signature Program>Microsoft Windows Hardware Compatibility Publisher). After automatically identifying the hardware device at boot, reinstall the driver you downloaded that has passed Microsoft digital signature certification (WHQL). , and then restart the computer again to see if there is any improvement.
Then there are conflicts caused by software with duplicate functions in the system (such as installing 2 or more anti-virus software, firewalls, and ad blocking). To.
If it is confirmed that it is not a system or software problem, you need to test the hardware in the following order. First, the memory is most likely, then the CPU, then the hard disk, and finally the graphics card. The motherboard will basically not Blue screen.
In addition, you need to check whether poor heat dissipation is causing the machine to overheat (if so, you must install a more powerful radiator, re-coat thermal grease, and replace a powerful fan).
Check it out Check whether the top of the motherboard capacitor is bulging (if so, it must be replaced immediately).
It is also necessary to check whether the chassis power supply is insufficient, causing the output voltage to be unstable (if so, it must be replaced immediately)
< p> If the power-on self-test fails and no "beep" sound is heard, there must be a hardware failure. A preliminary judgment is required from the alarm sound of the small speaker (buzzer) in order to narrow the scope of the hardware failure. Please refer to your computer for the specific meaning of the power-on alarm sound. Motherboard manual.2. If the self-test fails, there must be a hardware failure:
What should I do if I do not hear a beep after the computer starts the self-test?
If the computer fails to self-check after startup and does not hear a beep, there must be a hardware failure.
It is necessary to troubleshoot and check from the following aspects:
1. System The time cannot be displayed and saved correctly due to insufficient battery power on the motherboard. This type of fault can be solved by replacing the motherboard battery with a new one, and pressing the DEL key to enter the BIOS after booting to reset the correct system time.
2. Check whether the motherboard capacitor is bulging or leaking. If so, you need to go to a professional computer repair place to replace the motherboard capacitor.
3. Unplug the memory stick, wipe the gold finger with an eraser and reinsert it Return to the memory slot.
4. Reinsert all hardware and cables firmly to avoid virtual connections.
5. Start the computer once with the case open and check the fan If it is running normally, it needs to be replaced.
6. Check whether the power supply of the chassis is insufficient. If you have a replacement power supply on hand, try replacing it.
7. Is there a hard disk failure? There may be bad sectors. Please enter the BIOS to see if the hard drive can be recognized.
8. There is no signal on the monitor. Focus on checking the connection of the display part. If the monitor has a black screen or blurry screen, it may be a problem with the graphics card or the monitor itself.< /p>
9. Make a preliminary judgment based on the alarm sound from the small speaker (buzzer) of the boot case and your specific BIOS to narrow down the scope of the problem. Please refer to your motherboard manual for the specific meaning of the startup alarm sound.
10. That’s all I can think of for the time being. Other components should be checked step by step using the substitution method or the minimum loading method. Use the Chinese USB flash drive to enter the pe system and select win7 installation and it will not be installed automatically after restarting.
Enter the PE system of the USB disk - on the desktop of the PE system. Repair the boot... You can repair XP and WIN7 and the boot.
How to install the WIN7 installation version using Chinese cabbage?
You can prepare a system installation CD and install the system through the system disk. The specific steps are as follows:
1. Put the system CD into the optical drive;
< p> 2. Restart the computer, click the ESC key after booting, select the DVD drive startup item through the arrow keys on the keyboard, and click the Enter key to enter the system installation interface;3. The Windows 7 installation interface appears. First, select Chinese (Simplified), Chinese (Simplified, China), Chinese (Simplified) - American keyboard. After selecting, click Next. After clicking Install, the installation program is starting;
4. Now When the agreement appears, check the box that accepts the license terms and proceed with the installation;
5. Select Customize in the selection interface that appears: select the first partition here, the type is system, and then click In the next step (before this we can format our first partition, go to Drive Options (Advanced) (A)), the installation interface will appear. After waiting for a while, the installer will be reminded that the service is starting;
< p> 6. Remind you that the installation process will continue after restarting your computer, which is fully automatic;7. The startup and Windows screens will appear on the desktop, and the installation program is checking video performance;
8. After the installation is completed, the user name input interface will appear. Enter the user name. After the next step, the password input interface will appear. Confirm whether to enter the password as needed, and then take the next step;
9. When you need to enter a key, you can enter the system activation key;
10. Choose to install only important updates, and adjust the time and select the network;
11. Then Windows7 The flagship version is starting, so you have entered the system;
12. After the system installation is completed, you can go to the official website driver download page to download and update the driver of the machine. How to activate Dabaicai win10 after installation
The first is to upgrade from the original system to win10. This method is the easiest and is highly recommended. After downloading the ISO image of win10, use a virtual optical drive to load it (you can use a Rubik's Cube virtual optical drive, etc.), then double-click SETUP.EXE in the running directory, and then start the installation.
After accepting the license terms, the installation begins.
Win10 will automatically check the installation environment of your computer, which will take a few minutes. If there are a lot of software installed on your computer, it will take longer. Just click "OK".
If your computer does not have missing system functions or software compatibility issues, the following page will appear, select "Install".
It is very important to choose the content to be retained after the upgrade. Be sure to read it carefully before choosing. Then take the next step.
6
After starting the installation, all that is left is to wait. During this period, the computer will restart several times, and the system will be automatically installed. You can go to eat first, and it should be installed after eating.
7
The second method is to use U disk PE to install win10. There are many tools for making U disk PE, such as Chinese cabbage, Laomaotao U disk PE, etc. They are very convenient. It is very simple to create a USB bootable disk with the key. After the production is completed, the installation begins. After inserting the USB flash drive made by the USB flash drive to start, turn on the computer, and then press the shortcut key to select the startup item. Many brands including Lenovo press F12, Asus presses ESC, and Dell seems to use F9. Try these and you will definitely get it right. . How to boot and install XP.WIN7 with Chinese cabbage U disk
First copy the XP or win7 installation file or GHOST file to the U disk, insert the U disk, set the U disk boot in the BIOS, and then boot It will enter the U disk, open My Computer there, click the installation file setup you copied to the U disk or the manual GHOST on the desktop. After opening the interface, select items 1, 2, and 3, and then install the system with the CD. It’s the same, just be careful when selecting multiple hard drives. How to use Chinese cabbage PE to install win7 image?
U disk installation system steps:
1. Use the Dabaicai U disk boot disk creation tool to create a U disk boot disk, and download the genuine system image or pure version image, the download suffix is Copy the ISO image file to the root directory of the USB disk.
2. Turn on the computer and press the F2 key to enter the BIOS settings. Select the BOOT option—Secure Boot and set it to "Disabled". Select OS Mode Selection and set it to CSM OS. Select Advanced. Set Fast Bios Mode to "Disabled" under the menu and press F10 to save and exit.
3. Restart the computer and press the F10 key to enter the fast boot startup, select the USB flash drive to boot into Windows PE, use the hard disk tool partition format, set the main boot partition to C drive, and use third-party recovery software to restore the image file How to install ghost win7 using Dabaicai USB flash drive to the C drive
1. Format the USB flash drive and set the USB flash drive partition to BOOTABLE. You can use the partition tool to set it. (Key!) 2. Unzip WIN7 into a USB flash drive. You can use WINRAR to unzip it directly. If the capacity is less than 4G, you can only decompress the key startup files (refer to the hard disk installation method) and decompress all the contents to the hard disk, but the installation will be more troublesome. 3. Set the computer to boot as USB-HDD and follow the prompts to complete it step by step. If the capacity is less than 4G, you need to boot the USB flash drive to Advanced System Repair --> DOS, then select the file decompressed on the hard drive and run SETUP on the hard drive to install it, which will be a little troublesome.
Preparatory work:
1. Download the U disk tool software USBOOT
2. Download the USB-HDD-WINPE file
3 , Extract the system image file (WIN7.GHO file)
Start U disk production:
1. Plug in the U disk, start the USBOOT software, select the USB-HDD mode as the working mode, and click Production (after completion, you can use the newly produced U disk to start the computer. If the C prompt appears, it means that the U disk has passed the test and you can continue the operation). 2. Unzip the downloaded USB-HDD-WINPE file and copy all the files in the folder to the root directory of the U disk. 3. Copy the extracted system image file to the root directory of the USB flash drive.
Instructions for use: 1. Plug in the newly made USB flash drive, restart the computer, enter CMOS, set the first boot to USB-HDD, F10, press Enter to restart.
2. After booting for a few seconds, enter the Chinese boot interface, select "Enter Mini WINPE System" and press Enter;
3. After entering the WINPE system interface, click Start-Program-GHOST32, Run GHOST32;
4. After running the GHOST32 program, manually select the WIN7.GHO file in the U disk to hard disk C. (Note: If you do not know how to run GHOST manually, skip this step and read the supplement!)
5. When prompted that GHOST is completed, restart the computer (you can remove the U disk). If the U disk is still inserted into the computer, the startup screen will appear. Select "Start the computer from the hard drive." The system enters the automatic installation and file copying stage.
6. The computer automatically restarts and the installation is successful!