Current location - Quotes Website - Team slogan - How does fitter do a good job in safe and civilized operation during internship? What are the specific measures?
How does fitter do a good job in safe and civilized operation during internship? What are the specific measures?
1. 1. Wear labor protection articles according to regulations before operation, and the braids of female workers must be included in the hat. If electrical equipment and tools are used, the grounding wire should be checked as required and insulation measures should be taken.

1.2. It is forbidden to use unqualified tools such as cracks, burrs and loose handles, and strictly abide by the safety operation procedures of commonly used tools.

1.3. gloves are not allowed when drilling and hammering. When drilling with a drilling machine, you must abide by the "Safety Operation Rules of Drilling Machine".

1.4, tools must be used to remove iron filings, and it is forbidden to hold them with your hands and blow them with your mouth.

1.5. When picking and shoveling workpieces, no one is allowed in front. When picking and shoveling workpieces, a baffle or wire fence should be set in front of the fixed workbench.

1.6. Pay attention to the safety of people around you and yourself when working, and prevent workpieces and tools from falling off and iron filings from splashing and hurting people. When two or more people are working, one person should be in charge of the command.

1.7, equipment maintenance, safety maintenance ticket must be handled before work, before entering the equipment maintenance, the work permit for entering the equipment and containers must be handled in advance, and the hot work permit must be handled in advance when entering the inflammable and explosive materials maintenance equipment.

1.8. When the equipment is overhauled (inspected), the "Contact Sheet for Power Transmission Stopped during Equipment Overhaul" shall be handled, and the electrician shall stop power transmission and take safety measures according to regulations. The operator can directly stop the power-off equipment without going through an electrician. During maintenance, if necessary, lock the knife switch or hang a "No Closing" sign at the knife switch.

1.9. When cleaning equipment workpieces, it is forbidden to use volatile flammable liquids, such as gasoline, benzene, acetone, etc. Fire prevention measures should be taken when necessary.

1. 10, when using electrical equipment in wet places and rainy days, it must be checked by an electrician before use.

1. 1 1. During scraping operation, the workpiece must be smooth, and the scraper is not allowed to operate on people. When grinding large crankshafts and headstock, safety devices or skids should be set or appropriate safety measures should be taken.

1. 12. When using the pig, check whether the hose, flexible shaft and electrical grounding are in good condition, and the pig connection should be tightened. The switch signals operated by two people must be clear and well coordinated, and pigging with gloves is not allowed.

1. 13. The periphery of the marking desk should be kept clean, and it is forbidden to pile up articles within one meter. The bottom and top of the jack used must be flush, and the thread mouth should be tight. Sliding jacks are prohibited. Jack is not allowed to tilt, the bottom should be padded, and sleepers should also be padded. Other personnel shall abide by the safe operation procedures of jack.

1. 14, the workpiece mark should be supported firmly. When supporting a large workpiece, it is forbidden to put your hands under the workpiece. If necessary, you should use a bracket or crane to lift it. If you can't finish it that day, take precautions.

1. 15, purple alcohol for marking, no naked flame within three meters, no baking on the heater or gas stove.

1. 16, when using small lifting equipment such as chains and jacks. , must abide by the lifting safety operation procedures.

1. 17. When moving objects manually, it is necessary to have unified command, make steady progress and keep the same slogan.

1. 18, check the disassembly or assembly work when stopping or resting halfway, and the parts must be put safely.

1. 19. When working at heights and using ladders, the "Safety Operation Rules for Working at Heights" and "Safety Precautions for Using Ladders" shall be observed.

1.20. Before the commissioning of mechanical equipment, check whether all parts of mechanical equipment are in good condition. After the maintenance personnel leave the site, go through the formalities of stopping power transmission, and contact with rotating parts shall not be adjusted during the commissioning.

1.2 1, stop the car and cut off the power after work or leave the post for some reason.

1.22, safety helmet and tool kit must be worn to prevent falling objects from injuring people, and unified command should be paid attention to.

1.23, aerial work, must deal with the high work permit, tools used in the operation, must be tied with rope or set up other protective measures, so as to avoid accidental fall.