From the main menu → Network Management, enter the network parameter setting interface, as shown in the following figure:

There are four networking modes to choose from: manually configuring IP, automatically obtaining DHCP, ADSL dialing and wireless network card.

5. 1 Configure IP manually

Manually enter the IP address assigned to this machine. Fill in "subnet mask"/"gateway" according to the network environment where DVR is located.

1. If there is no router device in the network, please assign the IP address of the same network segment;

2. If there are routing devices in the network, you need to set up corresponding gateways. "DNS" is to set the IP address of the domain name server (each city is different). After setting, click Save to take effect.

You can refer to the network setting method of personal computer.

5.2 DHCP

Select Automatically configure local network parameters, and then save the settings. After the system is refreshed or restarted later, it will automatically establish a connection with the DHCP server. After successful connection, the device will be assigned an IP address and displayed in the IP column.

Note: Before using DHCP, please ensure that the DHCP service is enabled locally.

5.3 ADSL dialing

Click Dial in the network management interface to enter the PPPOE setting interface, as shown below:

Connection: Fill in the user name and password provided by ISP in "User Name" and "Password". Click Connect to automatically establish a network connection. After the connection is successful, "Connected" will be displayed, and the IP address bar will be automatically changed to the dynamic IP address of the WAN.

Disconnect: Click the "Disconnect" button to disconnect ADSL dial-up connection.

5.4 wireless network card

Connection: You need to connect the wireless network card to the USB port first; Then enter the corresponding number, user name and password; Click Connect to establish a network connection. After success, "Connected" will be displayed, and the IP address will be automatically changed to the dynamic IP address of the WAN.

Disconnect: Click the Disconnect button to disconnect the wireless network.

Note: Huawei E 1750 is recommended.

JVS-D70 16 does not support wireless network cards.

5.5 Cloud Visual Digital

After successfully connecting to the Internet, the system will automatically apply for the number of Yunshitong. The sub-control terminal, IE monitoring terminal or mobile phone terminal can use this number to connect with the main control, and after the connection, they can remotely view the picture of the main control channel and perform corresponding operations.

The number of the cloud video link is A0 or B0: it means that the number has not been applied, and the following operations can be performed:

1. Confirm that the network service is normal.

2. Click on the product registration under the system settings to register.

3. Change the port number of Yunshitong to the value after 9 1 10.

Yunshitong number exists, indicating "Offline":

1. Wait 2 minutes, and then click the refresh button.

2. If you are still not online, you need to resume system operation to clear the original network configuration.

3. If the number is still not online after recovery, please contact technical support for help.

Cloud video port: When multiple DVRs are under the same router, you need to modify the cloud video port of each DVR (after 9 1 10 and different), and then click Save to restart the cloud video service.

5.5 Remote Connection Statistics

You can count all users' IP, ports and the number of connection channels connected to this machine.

Click ",,,"to realize the function of "turn to the first page, turn to the previous page, turn to the next page and turn to the last page" in turn;

1. Click any connection in the optional list with the left mouse button, and then click Disconnect to disconnect the selected connection;

2. Disconnect all points to disconnect all remote connections.

5.6 network services

1. Master: Select "Enable WEB Service" under the main menu → System Management → System Settings.

2. Client: After entering the IP address of the host in the address bar of the browser, you can download and install related controls, and users can remotely monitor the webpage after logging in.

The default port is: 80. If this port is occupied, it needs to be modified, for example, 88. At this point, you need to add the port number after the IP in the address bar, for example

Remote connection

1 customer classification

JVS-D7000 series network hard disk video recorder supports a variety of remote access, such as cloud video communication, browser access and mobile phone access. Features are as follows:

1. 1 cloud video communication control

Install it on a computer that needs remote access to DVR. After successful installation, start the software, and then connect the IP or cloud video number of DVR machine to perform various operations. The cloud video network control software is integrated in the "Cloud Video Centralized Monitoring" on the DVR random CD, or downloaded from the website of www.jovetech.com Company.

Advantages: powerful function; Disadvantages: Need to install software.

1.2 browser access

1. Users can download the control by entering the main IP address in the browser address bar, log in with the correct user name and password after installing the control, and connect the IP or cloud video number of DVR machine to realize page monitoring; Ⅱ. Install IE control directly from the "Centralized Monitoring of Yunshitong" in the DVR random CD.

Advantages: only the controls need to be installed; Disadvantages: Not as many functions as cloud video clients.

1.3 mobile phone access

Copy and install the mobile phone monitoring software in the mobile phone supporting Java. The installed software can be connected to the IP or cloud video number of DVR to realize the mobile phone monitoring access.

Advantages: it is not limited by location and does not need computer equipment; Disadvantages: Minimum functions.

2 Remote connection mode

There are two remote connection methods: cloud video signal connection and IP address connection. Introduction is as follows:

2. 1 yunshitong number

This product embeds the cloud video communication function, and supports the remote network monitoring by using the cloud video communication network transmission platform of Zhongwei Company. Remote connection access only needs to know the DVR's cloud video number and network user name/password, without other network settings.

The unique number of each DVR machine can be viewed from DVR interface, main menu → Network Settings → "Cloud Video Number". Only when the number of Yunshitong is correctly displayed as "A360" and "Online" can it be used normally. If the number of Yunshitong is empty or "offline", please check whether the network settings are correct.

2.2 IP address

When users know the IP address of DVR machines, they can also use the IP address for remote connection access. For users in the local area network, using IP connection can improve the connection quality.

If an Internet user connects to a machine in a local area network, port mapping is required.

3 cloud vision control

3. 1 Independent control device:

Ⅰ. Decompress the compressed file from the DVR disc, open the JSetup.exe, select "Install Zhongwei Network Sub-control System", and follow the prompts to install it.

Two. Log in to www.jovetech.com, click: Download Center-Zhongwei Branch Control Terminal Software and IE Plug-in-Zhongwei Yunshitong Network Branch Control System and IE Plug-in-click here to download, decompress and select "Install Zhongwei Network Branch Control System" to install.

After the installation is completed, there is an icon of "Zhongwei Transportation Communication Control System" on the desktop. Open, enter the default user name: abc and password: 123, and enter the sub-control interface.

The following figure shows the control interface displayed on the square screen when the DVR master is not connected:

If the monitor is widescreen, the sub-control interface adapts to the following interfaces:

These two interfaces depend on the display and have the same function.

3.2 Connection parameter setting

Click System Settings, click the Video Source and Grouping tab to enter the Settings interface, as shown in the figure below.

After selecting a group from the group setting drop-down list, the number of video sources contained in the group will be displayed in the list at the lower left. Click any video source such as "video source 1", and the setting data of "video source 1" will be displayed on the right.

Fill in "User Name"/"Access Password", and the user name/password is consistent with the list of main control | user management | network users. That is, verify that you have the right to connect to another DVR host.

A.IP address connection: Select "Use domain name or IP connection" and enter the IP address of the host at "Domain name or IP". If the port is not modified, it defaults to 9101; Otherwise, click OK to save the connection data of "video source 1";

B. Cloud video communication number connection: Do not select "Connect by using domain name or IP", enter the cloud video communication number displayed by the main control network at "Cloud video communication number", fill in the port number at "DVR host | network management | cloud video communication port", and click OK to save the connection data of "Video source 1".

Note: Before clicking OK, click Apply All to apply the setting of "Video Source 1" to all video sources in the group, instead of setting for each video source.

3.3 Connect the master control

After setting the connection parameters, there are three connection modes:

1. Click the "Connect All" button in the child control interface to connect all the windows of the currently selected child control group to the main control;

2. Right-click each window and select "Connect this window" to connect the master;

3. Click the button on the right and select the corresponding grouping. Double-click the video source in the list to connect to the master device.

After the connection is successful, the window displays the master channel screen. Right-click and select Disconnect this window to disconnect this window from the master.

Note: If the number of windows is not enough, you can click the more function button → split the screen to select the appropriate number (1/4/9/ 16/25).

3.4 channel video

A. Click and select the window successfully connected to the main control channel, and click the channel video button below to video the currently selected window;

B you can also right-click the window and select "video book window" for video recording.

When recording, right-click the window and select "Stop recording this window" to stop recording in this window. During video playback, you can retrieve and view the stored video.

If you want to control the video with channel sound, the owner needs to select the compression type of the corresponding channel as "Audio and Video" in "Channel Settings".